User manual YANMAR 3GM PARTS CATALOG

[. . . ] Turn off the power immediately if water leaks into the equipment or the equipment is emitting smoke or fire. Electrical shock can result. Antenna Unit Name: Radiation Warning Label Type: 16-016-1802-0 Code No. : 100-312-020 WARNING Any repair work must be done by a licensed radio technician. A warning label is attached to the terminal, communication and antenna units. If a label is missing or damaged, contact a YANMAR agent or dealer. WARNING To avoid electrical shock, do not remove cover. [. . . ] Professional Priority Service is checked on special agreement with the Net Provider, e. g. CONFIGURATION FROM PC 5. 13. 2 Testing the Distress Alarm Right clicking a Dedicated Handsets as indicated allows activating the buzzer in the Distress Alert Unit. Deleting an ISDN Handset Unplug the ISDN Handset to be deleted and rightclick the same in the Dedicated Handset list. Clicking Test Handset removes its data, leaving the Terminal Id and MSN number vacant for another Display Handset. in the Device Manager appears when a Display Handset is missing. 5-26 5. CONFIGURATION FROM PC 5. 13. 3 ISDN port Open device manager and click the New ISDN button to open ISDN Setup Wizard. Select the required service: · 4. 8 kbps standard speech service · 64 kbps speech service · 3. 1 kHz Audio · 56 kbps data service (V110) · 64 kbps data service (UDI) Click to continue. Check with Terminal Id received from Net provider. Key in MSN number if not using the recommended one. CONFIGURATION FROM PC 5. 13. 4 RS-232 port Open device manager and click [---] button of the RS232 on the Serial Ports64K UDI to open Serial Port Setup window. CONFIGURATION FROM PC 5. 13. 5 USB port Open device manager and click [---] button of the USB on the Serial Ports-64 K UDI. Click to open Serial Port Setup. USB Key in MSN number if no using the recommended one. CONFIGURATION FROM PC 5. 13. 6 Analogue port Open device manager and right-click the device in the Analog Telephony Ports box to open analogue port setup window. Select the required service: · 4. 8 kps standard speech service · 64 kbps speech service · 3. 1 kHz Audio Enter terminal ld (OID/DID) received from the Net provider. Click Next to continue. Key in MSN number if not using the recommemded one. Click OK to enter number. if two telephones are given the same MSN, they will both respond to an incoming call to that MSN. Echo Cancellation is performed automatically for all voice calls. The default settings are: Data speed: 115200 bps Format: 8 data bits, no parity, 1 stop bit Flow control: Hardware (RTS/CTS) Modem Drivers Win 2000/XP: - Std 33. 600 bps NMEA NMEA TEL 1 TEL 3 SILENCE ISDN ISDN IND SW RX RX RX RX TX TX TX TX ISDN ISDN TEL 4 TEL 2 TEL 4 RX RX RX RX RX RX TX TX TX TX TX TX ISDN ISDN TEL 3 USB RS-422 ISDN ISDN RS-232 B RS-232 A 3GM 54321 9876 PC serial port DTE 6-2 6. DATA COMMUNICATION 6. 1. 3 MPDS - setup (Windows XP is used as an example) Ensure that vtLite Marine is closed. 1 Open the Control Panel on the PC and double-click the Phone and Modem Options icon. 2 Click the Modems tab. DATA COMMUNICATION 3 In the Add Hardware Wizard window check "Don't detect my modem", and click Next. Select Standard 33600 bps Modem in the Models field, and click Next. 4 Select the port to which the Modem driver should be installed. DATA COMMUNICATION 5 Opening the Phone and Modem Options window confirms the established modem connection. Select "Standard 33600 bps Modem". Note: The setup for data transfer to the CU is based on the Windows 2000/XP default parameters: 8 data bits - no parity - 1 stop bit - flow ctrl: Hardware Clicking Properties allows checking the parameters. 6 Open the Control Panel on the PC and double-click the Network Connections icon. 6-5 6. DATA COMMUNICATION 7 Click Create a new connection to open the New Connection Wizard. DATA COMMUNICATION 9 Check "Connect using a dial-up modem". Click Next. 10 Check "Modem Standard 33600 bps Modem. " Click Next. [. . . ] To make an outgoing call, you use a standard international telephone number with the 00 prefix. The MES automatically includes information to identify itself and the particular device that originates. System signalling The LES uses the identifying information of the attached device for billing purposes. The MES transmits the dialing information on a channel specially assigned by the NCS to the LES. [. . . ]