User manual XTANT M410 TECHNICAL DATA REPORT
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual XTANT M410. We hope that this XTANT M410 user guide will be useful to you.
Manual abstract: user guide XTANT M410TECHNICAL DATA REPORT
Detailed instructions for use are in the User's Guide.
[. . . ] R e f e r t o t h e i l l u s t r ation on the reverse side of this document prior to setting the input sensitivity.
INSTALLER
DA T E
INSTALLED: N A M E:
'
S
REFERENCE
PHONE:
LOG
xtant technologies installer's reference
DOCUMENT H A S B E E N C R A F T E D T O M A K E I N S T A L L AT I O N, SYSTEM D E S I G N A N D TROUBLE- SHOOTING, A Q U I C K A N D E A S Y PROCESS. TH E C H A R T S P R O V I D E D, O F F E R A S I MP L E METHOD O F D O C U M E N T A T I O N.
OWNER'S A D D R E S S:
TH I S
CI T Y/ ST A T E: V E H I C L E: XT A N T
A M P L I F I E R: M O D E L
SETTING)
ZI P: YE A R:
S E R I A L#
CROSSOVER MODES OF OPERATION
T h e 6 0 4 x i s e q u i p p e d w i t h i n d e p e n d e n t FRONT a n d R E A R crossovers. [. . . ] Each crossover is controlled by four crossover mode jumpers labeled, FRONT CHAN XOVER MODE, LINE OUT MODE SELECT, REAR CHAN XOVER MODE, LINE OUT MODE SELECT. The header jumper labeled FRONT CHAN XOVER MODE controls the crossover function as it applies to the front channels. The header jumper labeled REAR CHAN XOVER MODE controls the crossover function as it applies to the rear channels. (See illustration) The t w o header j um per s l abel ed L I N E O U T MO D E SELEC T, control the crossover function as it applies to the front and rear, left and right line outputs. (See illustration) The High and Low Pass frequencies are determined by the Frequency Modules (SIPs) installed in the four (4) SIP sockets pictured on the reverse side of this document.
input sensitivity ( CIRCLE
F R O N T I N P U T S ( FRONT CHANNELS)
R E A R I N P U T S ( REAR CHANNELS)
20dB
10 dB
0dB
+10dB +20 dB
20 dB
10 dB
0 dB
+10 dB
+20 dB
IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. ON P A G E 1 2 O F T H E OWNER'S MA N U A L, Y O U W I L L F I N D T H E OWNER'S REFERENCE LOG. ONCE Y O U H A V E N O T A T E D T H E F I N A L SETTINGS F O R T H I S 6 0 4X, T R A N S F E R THOSE SETTINGS T O T H E OWNER'S REFERENCE LOG. Any combination of the available frequency modules (SIPs) may be used (ie. 80 Hz Low Pass and 120 Hz High Pass).
· · · · · · · · · · · · · · · ·
I N S T A L L A T I O N SPECIALIST D A T E I NSTALLED
ADJUST LEFT, RIGHT FRONT AND LEFT, RIGHT REAR AMPLIFIER OUTPUT LEVELS. ADJUST NOISE GATE THRESHOLD
(IF USED): T u r n n o i s e g a t e o n a n d a d j u s t t h e t h r e s h o l d b y t u r ning clockwise to increase sensitivity (gate will open w i t h l e s s i n p u t s i g n a l ) . T h e g r e e n LED w i l l i l l u m i n a t e when the gate passes signal.
AFTER FINE TUNING THE SYSTEM:
xtant technologies
·
·
·
·
·
·
·
·
·
7 6 7 6 SO U T H 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602 431. 8686
Remove protective covering from amplifier and clean per the maintenance section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base.
· · · · · · · · ·
INSTALLER'S . REFERENCE. . M410 .
CROSSOVER FREQUENCY SELECTION: TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REPLACE THE 90 HZ FREQUENCY MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD. NOTE THAT THE IDENTITY OF THE HIGH & LOW PASS SOCKETS ARE MARKED ON THE BOARD. [. . . ] . M410 .
CROSSOVER FREQUENCY SELECTION: TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REPLACE THE 90 HZ FREQUENCY MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD. NOTE THAT THE IDENTITY OF THE HIGH & LOW PASS SOCKETS ARE MARKED ON THE BOARD. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE XTANT M410
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual XTANT M410 will begin.