User manual X10 VK75A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual X10 VK75A. We hope that this X10 VK75A user guide will be useful to you.
Manual abstract: user guide X10 VK75A
Detailed instructions for use are in the User's Guide.
[. . . ] OWNER'S MANUAL
XM14A POWER SUPPLY
C1
CAM ERA
C2
C3
C4
P1
POSITION
P2
P3
Cente r
P4
Sweep
M
. O .
K
. A . C . . E . I. G
SCAN
XC18A CAMERA
Pro gra m
Normal
CR14A REMOTE
ZC15A PAN 'N TILT BASE
MODEL VK75A PAN 'N TILT CAMERA SYSTEM
INCLUDES ZC15A PAN 'N TILT BASE, XM14A ADDRESSABLE POWER SUPPLY, CR14A REMOTE, AND XC18A CAMERA
INTRODUCTION
The VK75A includes the ZC15A Pan `n Tilt Camera Base with XM14A remote controlled power supply, the XC18A Wireless Camera, and the CR14A remote control. The camera sends the picture and sound to a receiver that you connect to your TV, up to 100 ft. You can remotely control the camera's position (pan and tilt it) using a CR14A remote control.
CONTENTS
CONTROLS AND CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Install 4 AAA alkaline batteries (sold separately) in the remote's battery compartment.
"Tilts" up and down. Pressing any of these turns on that camera, and turns the other 3 off (Transceiver required). Sweeps thru the 4 stored positions for the selected camera.
Pro m gra
SINGLE CAMERA OPERATION
Press a left or right BLUE button at the top of the CR14A Remote to "Pan" the camera left or right. Press a BLUE up or down button to "Tilt" the camera up or down. Buttons P1 thru P4 are used to store 4 position settings for the camera. To store the first position for the camera, press the BLUE buttons to scan to the position you want. To store the second position for the camera, press the BLUE buttons to scan to the position you want. To store the third position for the camera, press the BLUE buttons to scan to the position you want. To store the fourth position for the camera, press the BLUE buttons to scan to the position you want. To clear all stored positions: Move the switch at the bottom to Program. Press Center then move the switch back to Normal.
C1
C AMERA
C2 C4 P2
POS N ITIO
C3 P1
Centers the camera.
. A .
P3
C ente r
P4
Swe ep
SC AN
M
. I . G
C
Normal
WITH THE SWITCH SET TO NORMAL:
Scans forward or backward thru cameras controlled by C1 thru C4. Hold to step every 6 seconds.
Set to the same letter as the Transceiver and camera power supplies.
Press P1, P2, P3 or P4 to move to any of the 4 positions stored for the camera. To stop scanning or movement to a stored position: Press any BLUE key on the remote while the camera is moving to stop the movement. For multiple camera systems a Transceiver is required, which then lets you turn the cameras on and off by remote control.
If you purchase multiple Pan 'n Tilt Cameras, and purchase a Transceiver (RR501 or TM751) the Remote lets you turn on any of 4 cameras or scan each of them in turn (forward or backward) so as to display the image from each camera in turn on your TV. You connect each camera (up to 4) to its own Pan 'n Tilt Base, plug each one into an Addressable Power Supply, and set each to a different number between 1-4, 5-8, 9-12, or 13-16
10
11
MULTI-CAMERA SYSTEMS
STOP!If you only own one Pan 'n Tilt Camera, you don't need to read any further. Buttons P1 thru P4 are used to store 4 position settings for each of the 4 cameras controlled by buttons C1 thru C4. to center the position for camera 4.
12
13
TROUBLESHOOTING
Press C1 then Press C2 then Press C3 then Press C4 then Sweep Sweep Sweep Sweep to sweep through camera 1's 4 stored positions. If you do not see a picture on your TV: Check that the Receiver and the Camera are on the same letter channel (A, B, C, or D). The channel switch on the Camera is located under the rubber plug on the base of the unit. Make sure you replace the plug afterwards if you intend to use the camera outdoors. [. . . ] If the camera gradually drifts off the positions you have programmed: This can happen if the positions you programmed do not cause the camera to pass through center. If you notice the positions that you programmed for sweep starting to drift out of position after a while, just press the Center button on the remote to reset the positions to where you programmed them. Or you can make the camera periodically center automatically as follows: Within 3 seconds after you plug the camera's power supply in, press P1, P2, P3, or P4 on the remote. Pressing P1 within 3 seconds after you power up forces the camera to recenter every 32 sweeps through the positions you have programmed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE X10 VK75A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual X10 VK75A will begin.