User manual WHIRLPOOL WED99HEDW INSTALLATION GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WED99HEDW. We hope that this WHIRLPOOL WED99HEDW user guide will be useful to you.


WHIRLPOOL WED99HEDW INSTALLATION GUIDE: Download the complete user guide (8113 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WED99HEDW USE & CARE GUIDE (5539 ko)
   WHIRLPOOL WED99HEDW WARRANTY INFORMATION (150 ko)
   WHIRLPOOL WED99HEDW DIMENSION GUIDE (319 ko)
   WHIRLPOOL WED99HEDW USE & CARE GUIDE (5539 ko)
   WHIRLPOOL WED99HEDW WARRANTY INFORMATION (150 ko)
   WHIRLPOOL WED99HEDW VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WED99HEDWINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Com INSTALLATION NOTES Date of purchase:__________________________________ Date of installation:________________________________ Installer:_________________________________________ Model number:____________________________________ Serial number:____________________________________ NOTES CONCERNANT L’INSTALLATION Date d’achat :______________________________________ Date d’installation :_________________________________ Installateur :_______________________________________ Numéro de modèle :_________________________________ Numéro de série :___________________________________ W10678946B W10678949B - SP Dryer Safety Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized. IMPORTANT: When discarding or storing your old clothes dryer, remove the door. Installation Requirements TOOLS AND PARTS Gather the required tools and parts before starting installation. [. . . ] The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING: Improper connection of the equipment- To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Screw in leveling legs SAVE THESE INSTRUCTIONS Using a wrench and tape measure, screw leveling legs into leg holes until bottom of foot is approximately 1/2" (13 mm) from bottom of dryer. € This connection may be used with either a power supply cord or a direct wire connection. Remove terminal block cover A B C D Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole below the terminal block opening (B) so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together. Prepare to connect neutral ground wire and neutral wire E B A Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. If your outlet looks like this: Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-Wire Power Supply Cord Connection”. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Connect remaining wires E B A Remove center terminal block screw (B). Remove neutral ground wire (E) from green external ground conductor screw (A). Connect neutral ground wire and neutral wire B E Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Prepare your 3-wire cable for direct connection 1" m) 25 m ( C Connect neutral ground wire (E) and place hooked end (hook facing right) of neutral wire (white or center wire) (C) of direct wire cable under center screw of terminal block (B). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Remove center screw A F B Connect ground wire (green or bare) (F) of direct wire cable under green external ground conductor screw (A). [. . . ] Using a T25® screwdriver, remove the 4 screws securing the door hinge to the dryer and lift up and out to remove the door. Move the door strike Using a T25® screwdriver, remove the 4 screws on the dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Using a T25® screwdriver, remove the 2 screws securing the door strike to the door frame of the dryer. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WED99HEDW




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WED99HEDW will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.