User manual WHIRLPOOL WED97HEXL INSTALLATION 7-2010

[. . . ] ELECTRIC DRYER INSTALLATION INSTRUCTIONS Para una version de estas instrucciones en español, visite www. Whirlpool. com DRYER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 InSTAllATIon REquIREmEnTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tools and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 locATIon REquIREmEnTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Finally, reinsert tab of terminal block cover into slot of dryer rear panel. now, go to Venting Requirements. Connect neutral wire (white or center) (C) of power supply cord to center, silver-colored terminal block screw (B). connect remaining wires 3-Wire Power Supply cord connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 3-wire receptacle (NEMA type 10-30R) 3-prong plug Connect remaining wires to outer terminal block screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. now, go to Venting Requirements. Spade terminals with upturned ends Ring terminals 9 Direct Wire Connection Direct wire strain relief 4-Wire Direct Wire connection ImPoRTAnT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 1. Prepare your 4-wire cable for direct connection 1" ) 5 mm (2 B C 5 (127 " mm ) Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief (C) through the hole below the terminal block opening (B). Reaching inside the terminal block opening, screw the removable conduit connector (A) onto the strain relief threads. Direct wire cable must have 5 ft. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Prepare to connect neutral ground wire and neutral wire E B A Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable. Remove center, silver-colored terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). If your wiring looks like this: 4-wire direct connection: Go to 4-Wire Direct connection on this page. 3-wire direct connection: Go to 3-Wire Direct connection on page 12. 10 3. connect neutral ground wire and neutral wire B E 3-Wire Direct Wire connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 1. Prepare your 3-wire cable for direct connection (25 m 1" m) C 3½" (89 m m) Connect neutral ground wire (E) and place hooked end (hook facing right) of neutral wire (white or center wire) (C) of direct wire cable under center screw of terminal block (B). Squeeze hooked ends together and tighten screw. Direct wire cable must have 5 ft. If using 3-wire cable with ground wire, cut bare wire even with outer covering. Remove center screw A F B Connect ground wire (green or bare) (F) of direct wire cable to external ground conductor screw (A). connect neutral wire B C Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Finally, reinsert tab of terminal block cover into slot of dryer rear panel. now, go to Venting Requirements. Place hooked end of neutral wire (white or center) (C) of direct wire cable under center terminal block screw (B), hook facing right. connect neutral ground wire and neutral wire B E C Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). [. . . ] Excessive scale buildup may lead to the need for certain part replacement or repair. select Air Only Temperature setting. q Select a Time Dry heated cycle, and start dryer. Do not Not Level lEVEl Not Level If dryer will not start, check the following: ·Controlsaresetinarunningor"On"position. ·Householdfuseisintactandtight, orcircuitbreaker has not tripped. [. . . ]