User manual WHIRLPOOL WDE350LVB DIMENSION GUIDE

[. . . ] The model/serial rating plate is located below the electronic control on oven frame. C F B* The range should be located for convenient use in the kitchen. To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12. 7 cm) beyond the bottom of the cabinets. To install the antitip bracket shipped with the range, see "Install Anti-Tip Bracket" section. [. . . ] Recessed installation area must provide complete enclosure around the recessed portion of the range. 27¹/" (69. 9 cm) height to underside of cooktop edge with leveling legs screwed all the way in* C. Model/serial number plate (located below the electronic control on oven frame) D. 23³/" (60. 3 cm) countertop notch to rear of cooktop *Range can be raised approximately 1" (2. 5 cm) by adjusting the leveling legs. **When installed in a 24" (61. 0 cm) base cabinet with 25" (63. 5 cm) countertop; front of oven door protrudes 2¹/" (6. 4 cm) beyond 24" (61. 0 cm) base cabinet. 3 Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64. 0 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91. 4 cm) countertop height. IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface. Electrical Requirements If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Check with a qualified electrical installer if you are not sure the range is properly grounded. This range must be connected to a grounded metal, permanent wiring system. Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22. 2 No. A copy of the above code standards can be obtained from: National Fire Protection Association One Batterymarch Park Quincy, MA 02269 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575 A B C D E H F Electrical Connection G To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. Using the Phillips screwdriver, mount anti-tip bracket to the support slat with the two #12 x 1/" screws provided. 5 Adjust Leveling Legs 1. If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs. This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position. NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard. Electrical Connection WARNING Electrical Shock Hazard Disconnect power before servicing. Failure to follow these instructions can result in death, fire, or electrical shock. This range is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together. Install a UL listed or CSA approved conduit connector to the junction box. WARNING Tip Over Hazard A child or adult can tip the range and be killed. Failure to follow these instructions can result in death or serious burns to children and adults. 2. Leveling legs can be loosened to add up to a maximum of 1" (2. 5 cm). A minimum of ³/" (5. 0 mm) is needed to engage the anti-tip bracket. NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs. [. . . ] When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket. Before sliding range into its final position, check that the antitip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation. A A. Route the flexible conduit from the range to the junction box through a UL listed or CSA approved conduit connector. UL listed or CSA approved conduit connector 7 Install Lower Trim Moving the Range WARNING Tip Over Hazard A child or adult can tip the range and be killed. [. . . ]