User manual WHIRLPOOL AKR 968 INSTALLATION

[. . . ] D INSTALLATIONSANLEITUNGEN Der Mindestabstand zwischen dem Kochfeld und der unteren Kante der Dunstabzugshaube muss bei Elektroplatten 50 cm und bei Gasherden oder kombinierten Herden 65 cm betragen. Schreiben die Installationsanweisungen des Gaskochfelds einen greren Abstand vor, ist dieser natrlich zu beachten. Sie sollten einen qualifizierten Techniker mit der Installation beauftragen. Schlieen Sie das Gert erst nach seiner kompletten Installation an das Stromnetz an. [. . . ] Remove the hole diagram, insert the wall plugs and fix the hood support bracket with two 5 x 45 mm screws. Fit the flue support bracket "G" to the wall and against the ceiling, use the support bracket as a hole diagram (if present, the small slot on the support must match the line drawn on the wall ), mark 2 holes with the pencil then drill the holes ( 8 mm) and finally insert 2 plugs. Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar located above the extraction motor unit. For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter operation, fix the deflector F to the flue support bracket G and connect the other end of the exhaust pipe to the deflector collar F. Apply the flues and fix them with two 2 screws (12a) to the flue support bracket "G" (12b). Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the hood. Refit the grease filter/s and check for correct hood operation. 5019 318 33259 D GB F NL E P I GR Fig. 1 1. Control panel Grease filter Grease filter release handle Halogen lamps Steam deflector Telescopic flue Side air outlets (for filter version only) Fig. 1 Control panel 1. Timer button The timer can be adjusted with increases or decreases of 1 minute, the default timer setting is 10 minutes. Within 5 seconds of pressing the "TIMER" button the system switches to setting mode, allowing the user to set the timer using the "-" and "+" buttons. If no setting is made within 5 seconds of choosing the Timer function or setting the time, the countdown starts. The timer countdown can be activated in the following way: - after pressing the TIMER button once (timer default setting); - press the TIMER button again within 5 seconds of setting the desired countdown time. Once the countdown has started, the timer can be cancelled by pressing the TIMER button. "-" Speed decrease / motor OFF button To switch the hood off, press the "-" button to decrease the speed until the motor switches off. "+" Speed increase / motor ON button To switch the hood on, press the "+" button: the motor switches on at the 1st speed. The speed sequence is 1-2-3-4, so with each successive touch of the button "+" the motor steps up to the next speed. If the motor is already at the 4th speed, a beep sounds when the "+" button is pressed. The standard operating time at this speed is 5 min, after which the hood switches to 2nd speed. To switch off the function before the set time, simply press the "-" button. 5019 318 33259 D GB F NL E P I GR Control panel special functions Setting the clock The clock can be set at any moment except when the timer function is in use. The clock can be displayed in the standard 12 hour clock version with a display from 1:00 to 12:59. Temperature alarm The hood is equipped with a temperature sensor that activates the motor at speed 2 if the ambient temperature around the display area exceeds 70 C (the system monitors the temperature read by the sensor every 250 ms). [. . . ] If provided with a plug, connect the hood to a power socket complying with current regulations and located in an accessible area. If it does not have a plug (direct connection to the power supply) or if the socket is not in an accessible place, fit a suitable double-pole switch that ensures complete disconnection from the power supply in category III overvoltage conditions, complying with the installation rules. WARNING: Before reconnecting the hood circuit to the power supply and checking correct operation, always make sure the power cable is correctly fitted and that it was NOT crushed in its housing during installation. Electrical connections Cleaning the hood Important!Failure to remove oil/grease (at least once a month) could result in fire. [. . . ]