User manual WHIRLPOOL AKR 951

[. . . ] Packing Packing materials are 100% recyclable and are marked with the recycling symbol . Comply with the local regulations for disposal. The packing materials (plastic bags, polystyrene, etc. ) are a potential source of danger and must be kept out of the reach of children. Product This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). By ensuring that this appliance is correctly scrapped, the user can help prevent potentially harmful consequences for the environment and the health of people. [. . . ] The discharge air must not be eliminated in a duct used to remove fumes produced by appliances operating on gas or other fuels, but must have a separate outlet. If the hood is used together with other appliances operating on gas or other fuels, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). Do not leave pans unattended when frying, since the cooking oil could catch fire. The hood is not a shelf, therefore do not overload or place objects on it. Do not use or leave the hood without its lamps correctly installed - risk of electric shock. The air sucked by the hood must not be eliminated through the same flue of the heating system or other appliances using gas or other fuels. 5019 318 33303 TR GB The mains voltage must match that given on the rating plate located inside the hood. If provided with a plug, connect the hood to a socket complying with the current regulations and located in an accessible area. If it does not have a plug (direct connection to the power supply) or if the plug is not in an accessible place, fit a suitable double-pole switch that ensures complete disconnection from the power supply in category III overvoltage conditions, complying with the installation rules. WARNING: Before reconnecting the hood circuit to the power supply and checking correct operation, always make sure the power cable is correctly fitted and that it was NOT crushed in its housing during installation. Make sure to have this operation carried out by a specialised technician. Electrical connection Cleaning the hood WARNING!Failure to remove oil/grease (at least once a month) could result in fire. Never use abrasive substances or alcohol. Before calling the After-Sales Service 1. Check to see if you can fix the problem yourself (see "Troubleshooting Guide"). Switch the appliance off and then on again to check if the problem has been eliminated. Specify: · the type of fault, · the product model given on the dataplate inside the hood, visible on removing the grease filters, · your full address, · your telephone number and area code, · the Service code (the number under the word SERVICE on the dataplate inside the hood, behind the grease filter). If any repairs are necessary, contact an authorised Service Centre (to ensure the use of original spare parts and correct repair). Failure to comply with these instructions can compromise the safety and quality of the product. AFTER-SALES SERVICE Before using the hood Please read these instructions carefully and keep them for future reference, in order to ensure best use of your hood. The packing materials (plastic bags, polystyrene, etc. ) are a potential source of danger and must be kept out of the reach of children. Make sure the hood has not been damaged during transport. Declaration of conformity This product has been designed, manufactured and put on the market in conformity with: - safety objectives of the "Low Voltage" Directive 2006/95/EC (which replaces 73/23/EEC as amended) - protection requirements of "EMC" Directive 89/336/EEC amended by Directive 93/68/EEC. Troubleshooting guide If the hood does not work: · Is the plug properly inserted in the power socket?If the hood is not extracting enough: · Is the right speed selected?· Is the lamp correctly fitted? 5019 318 33303 TR GB INSTALLATION - ASSEMBLY INSTRUCTIONS Expansion plugs are provided to secure the hood to most types of ceilings. However, a qualified technician is needed to make sure that the plugs are suitable for your ceiling. [. . . ] The exhaust duct must be long enough to vent externally (Extractor version) or reach the deflector F (Filter version). For Filter Version only: fit the deflector F sul on the truss and fix it to the bracket with 4 screws, then connect the exhuast duct to the collar on the deflector. Carry out the electrical connection to the mains power supply, only turn on the power supply with assembly completed. Fit the nuts with fixing hooks suppliedinside the top and bottom sections of the flues at the rectangular slots. [. . . ]