User manual WHIRLPOOL AKR 891

[. . . ] IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the attention symbol and the following terms: DANGER: WARNING: indicates a hazardous situation which, if not avoided, will cause serious injury. indicates a hazardous situation which, if not avoided, could cause serious injury. All safety warnings give specific details of the potential danger/warning present and indicate how to reduce risk of injury, damage and electric shock resulting from improper use of the appliance. [. . . ] Finish off with a dry cloth. IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. · Use detergents specifically designed for cleaning the appliance and follow the manufacturer instructions. IMPORTANT: clean the filters at least monthly to remove any oil or grease residuals. GB3 MAINTENANCE WARNING: Use safety gloves. Disconnect the appliance from the power supply. GREASE FILTERS The metal grease filter has unlimited duration. It should be washed at least once a month, either by hand, or by placing it in the dishwasher (use a short cycle and low temperature). If washed in the dishwasher, the grease filter surface may become matt. After the filter has been washed and dried, replace following the inverse procedure. REPLACING THE ALOGEN LAMPS WARNING: - Only use 20W MAX - G4 halogen lamps. 1. Insert the blade of a small flat screwdriver where indicated by the three points, and with a gentle pressure lift the cover from its position. Replace the cover (spring lock). ACTIVE CARBON FILTER (filter models only): The carbon filter must be washed once a month in the dishwasher at the highest possible temperature using a standard dishwasher detergent. It is recommended that nothing else is placed in the dishwasher when washing the filter. After washing, the carbon filter must be reactivated by placing it in the oven at a temperature of 100°C for 10 minutes. Replace the carbon filter every 3 years. Fitting the carbon filter: 1. Remove the filter holding frame by turning the "g" knobs 90°. Fit the "i" carbon filter inside the filter holder "h". To refit the filter holder and the grease filter follow the inverse procedure. GB4 ITEMS SUPPLIED Remove all components from their packaged. · Assembled hood with motor, light bulbs, perimeter suction panel and grease filters installed. · 1 Chimney support bracket · 1 Hood support bracket · Assembly and user instructions · 1 installation template · 6 Ø 8mm wall plugs · 6 Ø 5x45 screws · 2 Ø 2. 9x6. 5 screws · 2 Ø 3x9 screws · 1 - Torx T10 adapter · 1 - Torx T20 adapter · 1 discharge pipe adapter, Ø 120-125 INSTALLATION - PRELIMINARY ASSEMBLY INSTRUCTIONS The hood has been designed to be installed and used either as a "Suction Model", or as a "Filter Model". Suction model Cooking steam is sucked and channelled outside the house through a discharge duct (not supplied), fitted to the hood steam outlet. Ensure that they type of fitting between the hood steam outlet and the discharge duct fits correctly to both. Filtering model The air is filtered through one of the carbon filters and then resent to the room. Before using the hood ensure that the carbon filter/s has/have been installed. The hood should be installed away from particularly dirty areas, windows, doors and heat sources. [. . . ] The system promptly reacts to any Steam/Gas increase, and remains at the set speed for at least 1 minute before returning to the lower speed, or switching off. After the effect of the gas is terminated, when the environmental conditions have returned to those before cooking, the system switches off: Note: Each time the hood goes from OFF to Stand-by mode, the system enters "6th Sense" mode. To exit Automatic Operation press keys "2" or "3" (the "LD5" led or the "6" key go off), decreasing or increasing the automatic speed by one step, or press "1" to return to Stand-By mode. Carbon filter alarm reset key After 320 hours of operation, with the hood ON, the carbon filter alarm reset key comes on to indicate that the carbon filter needs cleaning. [. . . ]