User manual WHIRLPOOL AKR 804 INSTALLATION

[. . . ] Als de installatie-instructies van het kooktoestel op gas een grotere afstand aangeven, moet hiermee rekening gehouden worden. Geef het apparaat geen stroom totdat de installatie geheel voltooid is. Aangezien dit apparaat zwaar is, dient het door minstens twee of meer personen verplaatst en genstalleerd te worden. E FICHA DE INSTALACIN Distancia mnima desde los quemadores: 50 cm si las cocinas son elctricas y 70 cm si son a gas o mixtas. Si en las instrucciones de instalacin de la placa de cocina a gas se especifica una distancia mayor respecto a la indicada, es necesario tenerlo en cuenta. [. . . ] Fig. 5 Fix the lighting unit to the hood with 3 screws and crescent-shaped washers. Note: The inside rim of the lighting unit has chamfers which must match the fixing places. Fig. 6 Apply the aesthetic cap A to cover the hood, passing the interconnection electrical cable inside. Warning: Make sure the interconnection cable does not touch the lamps and arrange the excess part using the cable clamps located at the top of the hood. Fig. 7 Fix the hood to the fixing brackets and secure with 1 screw for each bracket (COMPULSORY FIXING). Fig. 8 Adjust the position of the hood by means of the adjustment screws D. Fig. 10 Fix the connection box F to the support bracket on the ceiling with 2 screws. Carry out the electrical connection and secure the cables with the cable clamp G with 2 screws. Replacement of the interconnection cable must be carried out by the authorised after-sales technical service. Fig. 11 Insert the cover E between the support cables, making sure they enter the special slots on the cover. Leave enough cable so that it passes easily through the slot obtained in the cover. Secure the cover with 3 grub screws already screwed (or to be screwed) on the support bracket B. Note: The 3 fixing screws secure the cover by virtue of the friction they exert on the cover itself, and therefore must not be completely tightened. Fig. 12 Apply the aesthetic tabs I (press-on) to cover the hood fixing rib points 5019 318 33241 D GB F NL E P I GR S N DK FIN LI25BA PRODUCT SHEET Control panel Preliminary information for correct use of the hood: Use the fastest speed setting for particularly concentrated steam and fumes. It is advisable to switch the hood on 5 minutes before starting to cook and leave it running for another 15 minutes at the end of cooking. The hood is equipped with a "TOUCH SENSOR" device able to determine when the control rod is touched by the user, thus enabling control of lights and speeds. Automatic switching on function The hood is equipped with a temperature sensor that activates the motor at extraction speed (power) 1 when the ambient temperature in the area surrounding the hood exceeds 70C. In any case, the user can still switch off or change the extraction speed (power) (refer to section "Extraction speed (power) control"). Extraction speed (power) control Top part Bottom part Extraction speed (power) selection is cyclic according to the speed sequence stand-by - 1 2 3 4 therefore every time the TOP PART of the control rod is touched the extraction speed (power) increases by one level and switches off (stand-by) if the rod is touched again when the hood is on extraction speed (power) 4. Note: Extraction speed (power) 4 remains on for 5 minutes, after which the extraction motor switches to speed 2. By touching the rod again the extraction motor switches off (Stand-by). Deactivation of carbon filter saturation signalling (for particular applications) Switch off the hood (refer to section "Extraction speed (power) control") Touch the TOP PART of the control rod for more than 5 seconds, the LED will flash GREEN (amber) indicating deactivation of carbon filter saturation signalling. To reactivate carbon filter saturation signalling, repeat the operation, and the LED will flash ORANGE. 5019 318 33241 D GB F NL E P I GR S N DK FIN LI25BA Maintenance ALWAYS disconnect the hood from the mains before performing maintenance. [. . . ] The hood is not a shelf, therefore do not overload or place objects on it. Do not use or leave the hood without its lamps correctly installed - risk of electric shock. Note: Always wear work gloves for all installation and maintenance operations. AFTER-SALES SERVICE Before calling the After-Sales Service 1. See if you can eliminate the problem on your own (refer to "Troubleshooting guide"). [. . . ]