User manual WHIRLPOOL AKM 359

[. . . ] - The appliance must be disconnected from the power supply before carrying out any installation work. - Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer's instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the user manual. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage or injury. [. . . ] · After connection to the gas supply, checkfor leaks with soapy water. Electrical connections · Hob electrical connection must be made before connecting the appliance to the electricity supply. · Electrical connection must be carried out in compliance with the regulations of the local electric utility company. · Make sure that the voltage indicated on the rating plate on the underside of the appliance corresponds to the domestic power supply voltage. · Regulations require that the appliance is earthed: use conductors (including the earth conductor) of the appropriate size only. · For electrical connection, use an H05 RR-F type cable as specified in the table "Power supply voltage". INSTALLATION AND FIXING The installer is responsible for any damage or injury resulting from incorrect installation. To guarantee correct operation, the appliance must be installed on a perfectly flat surface. If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any chips that could compromise appliance operation. Install a separating panel under the hob (no separation panel is needed in case of oven under the hob) · a) b) c) d) Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. Continuous natural air circulation is ensured through a clear opening in a wall of at least 100 cm2. This wall opening must be: permanent and in a wall to the outside of the room to be vented; made in such a way that it cannot be obstructed from the inside or outside (not even accidentally); protected by plastic grids, metallic mesh, etc. , taking care not to reduce the air vent effective area mentioned a bove; located near floor level and positioned so as not to interfere with the operation of the exhaust system Connecting to the terminal board Connect the yellow/green earth wire to the terminal with the symbol . Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. The power supply cable must be long enough to allow the hob to be removed from the worktop and must be positioned so as to avoid damage or overheating caused by contact with the base of the hob itself. Do not use extension leads. Power supply voltage Wires 230V ~ + 230-240V ~ + 230V 3 ~ + 400V 3N ~ + 400V 2N ~ + Amount x size 3 X 2. 5 mm2 3 X 2. 5 mm2 4 X 1. 5 mm2 5 X 1. 5 mm2 4 x 1. 5 mm2 Assembly 1. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of th e brackets so that they are flush with the worktop surface (fig. Fix the brackets with the 4 screws supplied (B) using the holes provided. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. [. . . ] · Switch the appliance off, wait 30 seconds then switch it on again. If after the above checks the fault persists, contact the nearest After-sales Service. Always provide: · a brief description of the fault; · the exact type and model; · the service number (number after the word Service on the rating plate. "See figure in the next page") is located on the underside of the cooktop or on the warranty booklet; · your complete address and phone number. [. . . ]