User manual WESTINGHOUSE MT90 ARM29 INSTALL GUIDE

[. . . ] page 3 To Solid Concrete, Cinder Block, or Brick Walls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4 1 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. Parts List PART # A 200-4413 B 200-4418 C 200-1052 D 200-4483 E 200-0441 F 200-0547 G 590-1089 H 5M9-025-X02 I J 560-9641 5S1-015-C04 QTY. 1 1 1 1 1 1 4 1 1 4 4 4 8 4 4 1 1 6 6 Before you start make sure all parts listed are included with your product. [. . . ] Tighten screws (J) with phillips screwdriver (not provided) and push screw head covers (K) over wood screw heads (J). 1 concrete surface N Drill holes and insert anchors (N) WARNING · Tighten concrete anchor bolts firmly, but do not overtighten. Overtightening can damage the bolts, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N. M. ). 2 A J N Place plate over anchors (N) and secure with screws (J) WARNING · Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. 3 Tighten all fasteners (J) J INCORRECT CUTAWAY VIEW K CORRECT mounting plate concrete mounting plate concrete plaster/ dry wall plaster/ dry wall A 4 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. WARNING · Failure to correctly mount swing arm with plastic cap at top as shown in detail 3 will result in product failure. · Improperly installed snap rings will result in product failure. · If you are uncertain that product is properly installed, call customer service. IMPORTANT: Be sure swing arm (E) is in correct position shown below with plastic cap at top. Next thread snap ring (I) into groove at bottom of axle (C) protruding from wall bracket (A) as shown. NOTE: Fit of axle (C) into wall bracket (A) and lower swing arm (E) will be tight. Gently tap into place with a hammer if necessary. DETAIL 3 1 groove C H H C I E A E I pre-installed snap ring groove 2 3 I Insert swivel weldment (B) through swing arm (E). Align holes in swivel bracket (D) with holes in swivel weldment (B) and secure with four M6 x 10 mm phillips screws (M) as shown. B E M B D D 5 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. FOR VESA 100 MOUNTING PATTERN Use four M4 screws (R) and four bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Use four center holes of bottom plate (Q) as shown below. FOR VESA 100 X 200 MOUNTING PATTERN Use six M4 screws (R) and six bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Align upper end of slots with flat panel mounting holes. FLAT PANEL FLAT PANEL S R VESA 100 MOUNTING PATTERN S R Q 100 x 200 MOUNTING PATTERN Q Use four M6 screws (M) to attach top plate (P) to bottom plate (Q) using phillips screwdriver (not provided). NOTE: Top plate (P) will have one set of threaded holes on one side and a set of non-threaded holes on the other side. Bottom plate (Q) will also have one set of threaded holes on one side and a set of non-threaded holes on the other side. All four M6 screws (M) should pass through non-threaded holes first and into threaded holes. Q P Q M P 6 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. AT FL OF L CK ANE BA P Attach roll pitch assembly (F) to top plate (P) using four M10 x 15 mm phillips screws (O). P FLAT PANEL MAY APPEAR DIFFERENT THAN ILLUSTRATED F O WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel. 1/4" of exposed thread as shown in detail. 1/4" L D L Hook roll pitch assembly (F)/flat panel onto swivel bracket (D). 7 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com Adjust tilt as needed and secure with two M8 x 16 mm screws (L). [. . . ] EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY. Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. [. . . ]