User manual WESTINGHOUSE MT80 TILT INSTALL GUIDE

[. . . ] 7 Removing Flat Panel Screen from Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Parts List AA BB CC DD EE FF GG HH MT80 TILT Description Qty. Part # wall mount 1 095-0254 left adapter bracket 1 095-0232 right adapter bracket 1 095-0230 Alligator® anchor 3 590-0097 #14 x 2. 5" hex head screw 3 5S1-015-C03 #10-32 x 1/2" socket head cap screw 2 520-1040 grommet 4 590-1176 4 mm allen wrench 1 560-1131 AA BB CC HH DD EE 3 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com FF GG ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Installation to Wood Stud Wall WARNING · Wall or mounting structure must be capable of supporting a minimum static load of 320 lb (145. 1 kg). 1 Note: Ensure top two holes on wall mount face up for proper installation as shown in fig 1. 1. Mark top hole through wall mount, and drill one 5/32" diameter pilot hole 2-1/2" deep. [. . . ] If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. INCORRECT Tighten all fasteners. SO LID CO NC RE TE AA CIN DE RB LO CK DD CORRECT concrete mount concrete CUTAWAY VIEW mount plaster/ dry wall plaster/ dry wall EE 5 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com fig. 1. 5 ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Installing Flat Panel Screen to Wall Mount 2 Note: Grommets (GG) are used to prevent easy horizontal adjustment after screen is installed. Place grommets (GG) onto lower hooks of left and right adapter brackets (BB, CC) as shown in figure 2. 1. Place left and right adapter brackets anywhere onto wall mount (AA) as shown in figure 2. 2. The latches (see figure 2. 3) at the bottom of the adapter brackets lock the screen onto the mount. Lock latches of adapter brackets with safety screws (FF) using wrench (HH) as shown in figure 2. 3. WARNING · Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. · Safety screws must be inserted and hand tightened into each bracket and safety latch. Failure to do so can cause screen to come off mount if hit accidentally. CAUTION · Do not tighten screws with excessive force. 2. 3 6 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Adjusting the Horizontal Position and Tilt of the Flat Panel Screen 3 For horizontal adjustment, slide screen from side to side. If grommets are attached, the screen must be picked up and placed in new position as shown in figure 3. 1. Insert wrench (HH) through mount (AA) to adjust tension screw, shown in figure 4. 2 and detail 1, to desired tension to balance your screen size and weight. Desired tension is achieved when screen tilts easily and stays in place. Note: Tension screw is only on right side of mount Push or pull from top or bottom of screen to adjust tilt as shown in figure 4. 1. The tilt can be adjusted to a maximum of 15° forward or 5° backward. To lock the screen into the desired position, tighten tension screw using wrench. 4 fig. · lb (4. 5 N. M. ) maximum torque. CAUTION · Be careful not to pinch fingers when pushing screen from the bottom. fig. 4. 2 HH HH DETAIL 1 7 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Removing Flat Panel Screen from Wall Mount 5 Remove safetey screws (FF) as shown in figures 5. 2. Simultaneously push latches away from screen as shown in figures 5. 1 and 5. 2, and then lift screen off of the wall mount. You may need the aid of another person to assist with this operation. WARNING · Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely remove the screen. fig. 5. 2. 2 8 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. [. . . ] If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB, CC) on back of screen, align to holes, and center on back of screen as shown in figure 2. 1. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers (O), and spacers as shown in figure 2. 2. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver. WARNING · Tighten screws so adapter brackets are firmly attached. [. . . ]