User manual WESTINGHOUSE MT80 THIN INSTALL GUIDE

[. . . ] 7 Adding Safety to Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Before you begin, make sure all parts shown are included with your product. Parts List AA BB CC DD EE FF Description Qty wall plate 1 adapter bracket 2 #14 x 2. 5" wood screw 4 M5 x . 8 x 25 mm socket head cap screw 2 Alligator® anchor 4 4 mm security allen wrench 1 MT80 THIN Part # 200-4629 200-4628 5S1-015-C04 520-9567 590-0097 560-1145 AA BB FF DD EE CC 3 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Installation to Single Wood Stud Wall WARNING · Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. 1 Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center of studs with pencil. Skip to step 2 on page 7. WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. [. . . ] It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. · Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components. 1 Use wall plate (AA), making sure that it is level, as a template to mark holes. Place wall plate over anchors and secure with #14 x 2. 5" screws (CC). Tighten all fasteners. 1 concrete surface EE Drill holes and insert anchors (EE). WARNING · Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. · lb (9 N. M. ). 2 AA CC EE Place plate (AA) over anchors (EE) and secure with screws (CC). 3 WARNING · Always attach concrete expansion anchors directly to load-bearing concrete. · Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. Tighten all fasteners. so lid co nc ret e AA CC EE cin de rb loc k INCORRECT CUTAWAY VIEW wall plate concrete wall plate CORRECT concrete plaster/ dry wall plaster/ dry wall 6 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen. Installing Flat Panel Screen to Wall Plate 2 Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Screen can be adjusted horizontally if desired. WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. BB BB AA detail 1 Adding Safety to Mount 3 Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten screws with 4 mm security allen wrench (FF). BB DD AA DETAIL 1 7 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last. OBTAINING WARRANTY SERVICE ­ To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to obtain a Return Merchandise Authorization ("RMA") and for other instructions regarding return and replacement or repair of the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA. EXCLUSIONS TO WARRANTY ­ This warranty does not cover damage caused by (a) service or repairs by anyone other than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in transit or otherwise. PROOF OR ORIGINAL PURCHASE ­ A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. [. . . ] **Note: If screws (I) do not engage with the threads inside the mounting hole then use screws (G). If screws (G) are not long enough then use screws (F). 3 of 4 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 01-18-05 SHEET #: 201-9325-1 For customer service call 1-866-287-5555. Installing Adapter Brackets 2 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2. 1. [. . . ]