User manual WESTINGHOUSE MT25 ARM18 INSTALL GUIDE

[. . . ] For mounting to wall start with step 7. Measure the width of your screen. Note: The dimension of half the width will be used for steps 3 and 4. WIDTH OF SCREEN For mounting to the side of a kitchen or bathroom cabinet ­ follow all steps below: To ensure the screen does not hit the wall when the arm is in the closed position and mounted to the side of your cabinet, do the following: Measure 1/2 the width of your screen and subtract 3/4". This dimension is the minimum space you need between the back wall and the wall plate mounting holes. If you would like your screen to swivel the full 180° over the outer edge of your cabinet, do the following: Measure 1/2 the width of your screen and add 1 3/8". [. . . ] Skip to step 9. fig 1. 1 CONCRETE WALL H Drill hole and insert anchor (H). fig 1. 2 WALL PLATE WARNING · Tighten concrete anchor bolts firmly, but do not overtighten. Overtightening can damage the bolts, greatly reducing their holding power. fig 1. 3 I H Place wall plate over anchor (H) and secure with screw (I). WARNING · Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. After repeating figure 1. 1, tighten all fasteners. CUTAWAY VIEW I H WALL PLATE 4 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 04-22-04 SHEET #: 095-9195-1 For customer service call 1-866-287-5555. For Wood Stud Walls, use a stud finder to locate center of stud. Attach wall plate to center of wood stud using two #14 wood screws (I). WOOD STUD WALL WARNING · Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. · Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. WALL PLATE I Note: This product is designed to accommodate screens with VESA® compliant hole pattern. For safe mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts. 2) Attach adapter bracket (L) to back of screen using four 10 mm screws (M) as indicated below. 3) If hole pattern is in a pocket, attach adapter bracket (L) to back of screen using four 20 mm screws (N) and four retaining spacers (O) as indicated below. FOR VESA 100 MOUNTING PATTERN: 1) Choose hole pattern indicated below. 2) Attach adapter bracket (L) to back of screen using four M4 x 10 mm screws (M) as indicated below. Note: If you don't get three complete turns in the screen inserts, use four M4 x 12 mm screws (K) instead of four M4 x 10 mm screws (M). L For screens with a hole pattern in a pocket, spacers (O) go between adapter bracket (L) and screen. L Note: LCD screen may appear slightly different than illustrated. 5 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 04-22-04 SHEET #: 095-9195-1 For customer service call 1-866-287-5555. Note: If the balljoint feels loose or too easy to adjust, slightly tighten cap socket screw until balljoint feels firmly in place. Insert two M5 x 10 mm screws (F) into top two holes of adapter bracket (L) leaving approximately 1/4" of exposed thread. With slots facing upward, hook screws onto wall arm balljoint as shown in figure 2. 1. Insert two M5 screws (F) through bottom holes of wall arm balljoint into adapter bracket (L) as shown in figure 2. 2. Tighten all screws (F). fig 2. 1 fig 2. 2 L F 1/4" L WALL ARM BALL JOINT CAP SOCKET SCREW F To obtain full range of motion and enough tension to hold the screen in any position, simply tighten or loosen cap socket screw a few turns using 4 mm allen wrench (J). CAUTION · Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the screen to fall. CAP SOCKET SCREW 6 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 04-22-04 SHEET #: 095-9195-1 For customer service call 1-866-287-5555. If more or less tension is desired in the arm pivot points, do the following: · To increase tension, turn socket screw clockwise with 3/16" allen wrench (G). [. . . ] EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION AND SCOPE TO THE TERMS OF THIS WARRANTY. Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. [. . . ]