User manual WESTINGHOUSE LCM-19V1

[. . . ] 7 OSD MENUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 BACKLIGHT CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 DISPLAY MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 IMAGE PROBLEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Overloading Outlets Do not overload electrical power sources when installing the LCD monitor. Overloading wall outlets, circuits, or extension cords can result in overheating, fire, or electric shock. The power supply cord should be routed away from foot traffic and contact with other objects. Periodically inspect the power cord and each end of the cord for wear or damage. Ventilation Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Keep the LCD monitor a minimum of four (4) inches away from any wall to assure sufficient airflow and ventilation. 2 SE-UM-1901-0502 To assure proper ventilation, do not block the openings by placing the product on a bed, sofa, rug or other similar surface. Do not place the product in a built-in installation, such as a bookcase or enclosed rack, unless proper ventilation is provided. The warranty does not cover repairs or attempted repairs by anyone not authorized by Westinghouse Digital. If the monitor begins to emit smoke, an abnormal noise, or a strange odor, immediately turn it off and unplug the power cord. If the LCD monitor will not be used for an extended period of time, unplug the power cord. 3 SE-UM-1901-0502 Cleaning the LCD Monitor · · MAKE SURE THE LCD MONITOR IS TURNED OFF NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR CASE 1. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner on a clean, soft, lint-free cloth, and wipe the screen. To Clean the Screen: To Clean the Case: 1. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-abrasive detergent on a clean, soft, lint-free cloth, then wipe the surface. Disclaimer Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on the LCD screen or case. Some chemical cleaners have been reported to damage the screen and/or LCD display case. Westinghouse Digital will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners. 4 SE-UM-1901-0502 Safety Guidelines Warning: This device must be operated with the original power supply, part number ADP-60CF A. CAUTION: The power supply outlet should be located near the equipment and should be easily accessible. Always use the appropriate AC cord that is certified for the individual country. Some examples are listed below: USA. . . . . . . . . . . . . . . . . UL Switzerland . . . . . Electric Appliance Control Act IMPORTANT NOTICE CONCERNING POWER CORD SELECTION The power cord set for this unit is enclosed and has been selected according to the country of destination and must be used to prevent electric shock. [. . . ] Plug another electrical device (like a radio) to the power outlet to verify that the outlet is supplying the proper voltage. No Image · · Make sure the power button is ON. Check whether the LCD monitor and computer power cords are plugged in and check the power supply. Power is ON but No Screen Image · · · Adjust the brightness and contrast levels. Make sure the VGA cable is securely connected to both the computer and monitor. "Out Of Range" Check the computer image output resolution and frequency and compare the value with the preset values of the computer's graphics card. Fuzzy Image · · · · · Adjust the Phase setting on the monitor. Image Too Bright or Too Dark Adjust the brightness and contrast levels using the OSD. Perform Auto Adjust. Distorted Image · · Reset the LCD monitor by performing the "Recall" function using the OSD. [. . . ]