User manual WACOM CINTIQ 20WSX

[. . . ] Installation Guide & Hardware Manual for Cintiq 20WSX (DTZ-2000W) Wacom Cintiq® 20WSX Installation Guide & Hardware Manual for Cintiq 20WSX (DTZ-2000W) English version 1. 0, January 15, 2007 Copyright Wacom Company, Limited, 2007 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. [. . . ] See Adjusting pitch and phase (VGA only) on page 39 for details. Tip: If you prefer to see the screen cursor slightly offset from the actual position of the pen tip, calibrate by clicking on a spot showing that offset from the crosshairs. For example, to have the screen cursor appear 1/10th of an inch above and to the left of the pen tip, calibrate by clicking on a spot 1/10th of an inch below and to the right of the crosshairs. Customizing Page 34 Learning more about Cintiq Refer to the electronic Software User's Manual for detailed information on customizing Cintiq. To view the manual, open the Wacom Tablet Control Panel and click on the HELP button. To read the Software User's Manual before installing Cintiq, first insert the Wacom Pen Tablet Driver CD into your computer's CD-ROM drive. You will need Adobe Reader or another . pdf viewer to view the Software User's Manual. Customizing Page 35 Adjusting the LCD monitor Factory presets, auto-sync, and user settings Factory presets: For optimal display quality, set your video card to Cintiq's native resolution of 1680 x 1050 pixels (WSXGA). Auto-sync: When connected as a VGA display, Cintiq attempts to automatically synchronize to the incoming signal. At the native resolution of 1680 x 1050, the vertical refresh frequency must be set to 60 Hz. For other resolutions, auto-sync will function when the horizontal frequency is between 30 to 82 kHz and the vertical frequency is between 50 to 75 Hz. If a specific resolution and vertical refresh frequency are not supported, you will see an "out of scan range" message. The auto-sync function automatically sets the horizontal and vertical screen position, as well as pitch and phase. If Cintiq does not automatically synchronize with the incoming signal, you can open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option to initiate display synchronization. Additional screen display adjustments can be manually made using the OSD controls. Color calibration: Changing the color, color temperature, contrast, brightness, or backlight from their default settings will invalidate the ICC color profile that was included on the driver CD. Working with on screen display settings Cintiq is equipped with an On Screen Display (OSD) function. The OSD function enables you to adjust and optimize a variety of display settings at the touch of a button. Simply reach over the top of the display unit to locate the buttons with your fingers. Note: Braille-style dots above the buttons help you to identify each one by touch. Digital/Analog (DVI/VGA) switch (up) (down) MENU button Use this button to open or close the OSD menu. ENTER button Activates or deactivates the selected OSD menu option. Selection buttons Use these buttons to select an option that can then be activated when you press the ENTER button. After activating a selected option, press the up button to increase a selected item value, and press the down button to decrease it. Customizing Page 36 The basic process for working with the OSD is as follows: · Press the MENU button to open the OSD main menu. When the option you want to adjust is highlighted, press the ENTER button. The current settings and adjustment sub-menu for that option will appear. · When you have made your changes, press the ENTER button to save. Note: All settings are automatically saved when the OSD menu closes and will be used the next time the unit receives a similar video signal. [. . . ] You should send the product, shipping charges prepaid, to the designated service location, accompanied by the return authorization number, your name, address and telephone number, proof of purchase date, and a description of the defect. Wacom will pay for return shipping by United Parcel Service or by an equivalent service as chosen by Wacom. Wacom's sole obligation and entire liability under this warranty shall be, at Wacom's option, either the repair or replacement of the defective product or parts thereof of which Wacom is notified during the Warranty Period; provided, however, that you are responsible for (i) the cost of transportation of the product to the designated service location and (ii) any loss or damage to the product resulting from such transportation. Wacom shall have no responsibility to repair or replace the product if the failure of the product has resulted from accident, abuse, misuse, negligence, or unauthorized modification or repair, or if it has been handled or stored other than in accordance with Wacom's storage instructions. [. . . ]