User manual US ROBOTICS 005687-03

[. . . ] This manual covers installation and operating instructions for the following 3Com modems: U. S. Robotics is a registered trademark and Connections, RapidComm, and x2 are trademarks of 3Com Corporation and its subsidiaries. Any other trademarks, trade names, or service marks used in this manual are the property of their respective owners. © 1998 3Com Corporation 7770 North Frontage Road Skokie, IL 60077-2690 All Rights Reserved IMPORTANT! [. . . ] When you are finished, click Exit to return to the Modem Configurator menu. Please refer to the main body of the manual and the "Glossary "for detailed information about the terminology and settings used in this screen. Click Help for quick definitions of terminology used in this screen. WARNING!Improper settings may cause your modem to function incorrectly, disconnect, or fail to connect at all. In the upper left hand corner of the screen you will see the current connection commands. 79 USING MODEM STATION DIALING/ANSWERING The next screen allows you to adjust how your modem initiates and receives calls. STORED NUMBERS The "Stored Numbers" screen displays the phone numbers currently stored in your modem's memory. Use this screen to edit or add numbers stored in the modem's memory. Using this screen, you can configure the following dial settings: 80 WAIT FOR CARRIER AUTO-ANSWER # OF RINGS SPEAKER OPERATION DIALING METHOD SPEAKER VOLUME To store a number in your modem's memory, simply click in one of the entry boxes. You can set your modem to automatically dial this USING MODEM STATION number when your computer is turned on or when it is reset. This is very useful if you are using your modem with a "dumb terminal" or know that you need to connect to a specific bulletin board or listing service. You can change stored numbers by highlighting them and then typing the new numbers in their place. Once you store your numbers, you can dial them by entering a single command from Terminal Mode: (for example: ATDS0, ATDS1, or ATDS2). Robotics modem comes with one phone number already stored in Position 0. If you haven't changed the default, typing ATDS0 will automatically dial the 3Com BBS. Once you enter the numbers you wish to store, click Save to Modem to store them. Click Exit to return to the Main menu. The last option, Restore Defaults, resets your modem to factory specifications. This option is available from many of the screens within Modem Station. TIP: Restore Defaults will set your modem back to factory specifications. It is a good place to start when troubleshooting. Using the Extended Information Screens The "Extended Information" screens provide important and useful information about your modem. We devote a separate section to the Extended Information screens so that we can explain 81 USING MODEM STATION what you'll see (and why it is important to you) as fully as possible. There are a series of commands used to obtain detailed information from U. S. Extended Information provides a convenient way to get that important information without memorizing the commands. From the "Detect New Modems" screen, click Extended Information. The "Extended Information" screen provides access to the following information about your modem: 82 ROM CHECKSUM PRODUCT ACTIVE PROFILE STORED PROFILE CONFIGURATION PROFILE LINK DIAGNOSTICS VxD CONFIGURATION DIAL/SECURITY Winmodem users will have access to VxD information via these screens. Click ROM Checksum to bring up the following screen. Technicians use the ROM Checksum to verify information stored in the modem's Read Only Memory. [. . . ] Le matériel doit également être installé en suivant une méthode acceptée de raccordment. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus n'empêche pas le dégradation du service dans certaines situations. Les réparations de matériel homologué doivent être effectuées par un centre d'entretien canadien autorisé désigné par le fournissuer. La compagnie de télécommunications peut demander à l'utilasateur de débrancher un appareil à la suite de réparations ou de modifications effectuées par l'utilasateur ou à cause de mauvais fonctionnement. [. . . ]