User manual TYAN TRINITY 510

[. . . ] Trinity 510 Manual Revision 2. 01 S2266 Copyright © TYAN Computer Corporation, 2001. No part of this manual may be reproduced or translated without prior written consent from TYAN Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective owners including, but not limited to the following. Intel, Intel Pentium, combinations thereof are trademarks of Intel Corporation. VIA, P4X266, P4X, and combinations thereof are trademarks VIA Technology Inc. [. . . ] (optional feature) VIA-3058 AC97 Audio VIA-3043 OnChip LAN OnChip LAN Boot ROM 23 http://www. TYAN. com 3. 8 Super IO Configuration Options related to the IO interface can be altered through the following. Enabling ports also requires you to enter the I/O address for that port unless you select Auto. Recommended config: 2F8 & IRQ3 3F8 & IRQ4 Enabled requires manual input of port parameters. Two-way protocol Enhanced Parallel Port may provide higher bandwidth if an EPP compliant device is used (e. g. Enhanced Compatibility Port may provide higher bandwidth if an ECP compliant device is used (e. g. (optional feature) Serial Port 1, 2 Serial 2 Mode Serial Base I/O Enabled Disabled 3F8, 2F8 3E8, 2E8 IRQ3 IRQ4 Serial Interrupt Parallel Port Enabled Disabled Auto Output Only Bi-directional EPP Parallel Port Mode ECP Parallel Address Parallel IRQ 378 278 3BC IRQ5 IRQ7 DMA1 DMA2 201 330 10 ECP DMA Channel Game Port Address MIDI Port Address MIDI Port IRQ 24 http://www. TYAN. com 3. 9 Power Management Setup Options related to power management can be altered through the following. Enabled Disabled S1 (POS) User Define Maximum Saving Minimum Saving Disabled 1, 5, 10, 20, 30, 45, 60 minutes Disabled Standby Sleep Suspend -> Off Standby V/H SYNC+Blank Blank Off Instant-Off 4-seconds Off On Toggles advanced power and configuration done by OS. Defines whether the system will remain off if power fails or turn on when power is restored. ACPI function ACPI Suspend Type Power Management Option HDD Power Down Suspend Mode Video Off Option Video Off Method Soft-Off by PWRBTN PWRON After PWR-Fail IEQ/Event Activity Detect Press Enter 3. 10 IRQ/Event Activity Detect Options related to IRQ events can be altered through the following. VGA LPT & COM HDD & FDD PCI Master PowerOn by PCI Card Off On LPT/COM LPT COM On Off On Off Disabled Enabled Disabled Enabled Disabled Enabled Press Enter Defines whether the device will remain active if system enters Suspend mode. Modem Ring Resume RTC Alarm Resume IRQs Activity Monitoring 3. 11 IRQs Activity Monitoring Leave all settings as they are. Defines whether the system can be powered on by a PCI Card. Leave all settings as is. 25 http://www. TYAN. com 3. 12 Frequency/Voltage Control Options related to Frequency and voltages can be altered through the following. TYAN does not recommend changing this setting from the default setting. Sets the BIOS to automatically adjust CPI and memory bus speeds accordingly. Overclocking is not recommended by TYAN. Auto Detect PCI/DIMM Clk Enabled Disabled Spread Spectrum Enabled Disabled CPU host/3V66/PCI Clock Default 100/66/33MHz 103/69/34MHz 107/71/36MHz 110/73/37MHz Note: Although user-adjustable speed settings are provided, TYAN does not support anything other than the default speeds that the motherboard and processor were designed to operate at. 3. 13 Exit Options related exiting and saving can be done using the following. Save & Exit Exit Without Saving Load Setup Defaults Load Fail-Safe Defaults Load Optimized Defaults Exit and save options. Discard any changes made but use optimal options. 26 http://www. TYAN. com 4. 0 Installing the hard drives Hard drives must be of the Fast ATA-2, EIDE, or UltraDMA-33/66/100 type if you want to use them with the IDE controller. For best performance, we recommend that you use drives of identical model and capacity. If you are planning to use an UDMA-66 or 100 drive, you must use an UltraDMA-66/100 cable (TYAN has included that cable with the motherboard). Step 1: The first step is to set the hard drive to Master, Slave, or Cable Select setting, and install them according to the table below. Note: Sometimes the Master drive with no Slave attached is called "single". The Master/Slave setting differentiates two drives connected on the same cable. NOTE: Check your HDD documentation for master, slave, and cable select settings. Jumper Settings (see your HDD documentation for jumper settings) # of Drives 1 2 3 4 IDE Channel 1 M M M&S M&S M=Master, S=Slave IDE Channel 2 M M M&S Step 2: Next, you should install the drives into your Primary IDE controller, and connect the power. Attach one UltraDMA cable (black connector) to each drive (if you have a Slave drive, connect that drive to the second connector (grey connector) on the UltraDMA cable). Make sure that Pin 1 on the cable (indicated by the colored stripe) is connected to Pin 1 of the hard drive. [. . . ] Standby mode: in this mode, the video and hard drives shut down; all other devices continue to operate normally. Striping: see RAID UltraDMA-33/66/100: a fast version of the old DMA channel. Without proper UltraDMA controller, your system cannot take advantage of higher data transfer rates of the new UltraDMA/UltraATA hard drives. This one port type can function as a serial, parallel, mouse, keyboard or joystick port. [. . . ]