User manual STRONG SRT 5203

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and servicing instructions in the literature accompanying the appliance. Read the following instructions carefully TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT The apparatus shall not be exposed to dripping or splashing, and that no objects filled with liquids, such as vases, shall be place on the apparatus. WARNING: IMPORTANT SAFEGUARDS In addition to the careful attention devoted to quality standards in the manufacture of your product, safety is a major factor in the design of every instrument. [. . . ] Do not open or disassemble the outer chassis in order to avoid the danger of electric shock and damaging to the receiver. The antenna connected to the receiver shall be equipped with anti-shock device from lightning. Where the mains plug or an appliance coupler is used as the disconnected device, the disconnected device shall remain readily operable. This receiver has been manufactured to satisfy international safety standards. MAINS SUPPLY: AC 90 ~ 240 V ~ 50/60 Hz OVERLOADING: Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. CLEANING: Before cleaning, disconnect the receiver from the wall socket. Use a cloth lightly dampened with water (no solvents) to clean the exterior. Never store the receiver where it is exposed to direct sunlight or near heating equipment e. g. ATTACHMENTS: Do not use any attachment that is not recommended by the manufacturer; it may cause a hazard or damage the equipment. CONNECTION: Connect all components before plugging any power cords into the wall outlet. Always turn off the receiver, TV and other components before you connect or disconnect any cables. n By using "Advanced Installation", "Language select", "TV/VCR settings", "Time settings" and "Antenna settings" be defined manually. Here you can set up; Menu language, 1st Audio lang and 2nd audio lang and 1st text lang and 2nd text lang n Choose "TV/VCR settings" by using the pqtu buttons. Here you can set up; HDMI output, TV Screen Format, Picture Format and HDCP Always Enabled n Choose "Time settings" by using the pqtu buttons. Here you can set up; Country, Time zone selection, preferred Time zone and if daylight savings time should be activated. Here you can set up antenna supply n When you have made the changes you want, press BLUE "Save&Next" to go to the next step. 4. 3 Channel Search In this menu you can select a channel with signal to adjust your antenna for max signal en reception n Select "MUX" to choose a channel to test signal strength. n Select "Frequency" to manually enter a frequency to test signal strength. NOTE: the bandwidth changes automatically n Press OK to start scanning process. When the search is done and all channels have been found, a list of favorite networks will be shown and you have to select your favorite network. After this the receiver will automatically switch to the first channel in the list. PART 2 · English 5. 0 MAIN MENU In the Main Menu you find Channel manager, Installation, Timer and Information. 5. 1 Channel manager 1. Manage Channels Press OK to choose sub menus and pq to choose between the submenus. Sort Channels n Press RED "Sort" to see the options for automatic sorting of the channels. [. . . ] Press OK button to switch to the desired channel. n n n 6. 4 Volume Control The volume level of the receiver can be altered with the VOL+ or VOL- on the remote control. NOTE: n The volume level selected will remain set, even when the receiver is turned off and on again, until it's altered. The sound remains muted until the button is pressed again or the VOL+ or VOL- button is pressed or until the receiver is turned off and on again. 6. 5 Audio control n You can press the AUDIO button to select different audio tracks 6. 6 Accessing the favorite channels n n n Press FAV button Select one of the favorite list and press OK. Alternately you can press OK and use tu to select the favorite list 6. 7 Teletext n n Press TEXT button to start teletext function. Press EXIT to stop Text function. 6. 8 Subtitle n Press the SUB button to enter the subtitle menu and use pq to select the desired subtitle and press OK to activate. 6. 9 Show program information 1. [. . . ]