User manual SONY SU-WL500 INSTALLATION GUIDE

[. . . ] For other TVs, refer to their operating instructions to check if this Wall-Mount Bracket can be used. Some TVs are supplied with a leaflet explaining how to install the Wall-Mount Bracket ("Installing the Wall-Mount Bracket"). On Safety Products by Sony are designed with safety in mind. [. . . ] Consult your licensed contractor regarding an appropriate location (free from radio noise, etc. ) before installing. Be sure to use the supplied screws and attachment parts properly following the instructions given in this instruction manual. If you use substitute items, the TV may fall and cause bodily injury to someone or damage to the TV. Be sure to assemble the bracket properly following the instructed procedure explained in this instruction manual. If any of the screws are loose or fall out, the TV may fall and cause bodily injury to someone or damage to the TV. 4 (GB) Be sure to tighten the screws securely in the designated position. If you fail to do so, the TV may fall and cause bodily injury to someone or damage to the TV. Before installation If you intend to install a TV that is not specified on page 2, be sure to refer to the leaflet "Installing the WallMount Bracket" supplied with your TV. Be careful not to subject the TV to shock during installation. If the TV is exposed to shock, it may fall or break apart. This may cause injury. Be sure to install the TV on a wall that is both perpendicular and flat. If you fail to do so, the TV may fall and cause injury. Step 1: Checking the parts required for the installation 1 Prepare four or more 8 mm diameter or equivalent screws (not supplied) and a screwdriver. Unpack the carton and check to see that all the following items are included. After proper installation of the TV, secure the cables properly. If people or objects get tangled with cables, this may result in injury or damage to the TV. Do not allow the AC power cord or the connecting cable to be pinched. If the AC power cord or the connecting cable is pinched between the unit and the wall or is bent or twisted by force, the internal conductors may become exposed and cause a short circuit or an electrical break. This may cause a fire or an electric shock. 2 Be careful not to hurt your hands or fingers during the installation. Be careful not to hurt your hands or fingers when installing the Wall-Mount Bracket or the TV. Base Bracket (2) The screws needed to secure the Wall-Mount Bracket to the wall are not supplied. Use the appropriate screws for the wall material and structure when mounting the Wall-Mount Bracket. Mounting Hook (2) Screw (+PSW6 × 16) (4) Screw (+BVST4 × 12) (6) Hexagon wrench (1) 5 (GB) Step 2: Deciding on the installation location 1 Referring to the TV installation dimensions table on page 12, decide on the installation location. Allow for suitable clearance between the TV and the ceiling and protruding parts of the wall as shown below. Unit: mm 2 Referring to the Wall mounting dimensions diagram on page 13, determine the positions of the screws for installing the Base Bracket. WARNING The wall that the TV will be mounted on should be able to support a weight of at least four times that of the TV (Refer to your TV's instructions for its weight. ). Reinforce the wall sufficiently, if necessary. 100 300 100 Never install the TV set as shown below: Air circulation is blocked. 100 Wall Note If you intend to route the cables in the wall, make a hole in the wall to insert the cables before beginning the installation. 6 (GB) Step 3: Installing the Base Bracket on the wall 1 Secure the Base Bracket to the wall using four or more 8 mm diameter or equivalent screws (not supplied). 1 Determine the screw holes (d, h) for attaching the Mounting Hook to the Base Bracket. Then attach them securely using the supplied screws (+BVST4 × 12). Screw (+BVST4 × 12) 2 Secure the Base Bracket and the Mounting Hook on the wall using the four or more 8 mm diameter or equivalent screws (not supplied). Select four screw holes with the z mark shown in the diagram below and tighten the screws securely so that they will not become loose. Align the unit so that it is level. d g h Base Bracket 3 Remove the screws which were attached in procedure 1 and detach the Mounting Hook from the Base Bracket. Base Bracket Mounting Hook CAUTION Be careful not to drop the Mounting Hook when removing the screws from the Mounting Hook. WARNING · The screws required for this procedure are not supplied. · If the Base Bracket cannot be attached securely enough, use additional screws. · Be sure to confirm that the Base Bracket is securely attached to the wall. 7 (GB) Step 4: Preparing for the installation of the TV If you intend to install a TV that is not specified on page 2, be sure to refer to the leaflet "Installing the Wall-Mount Bracket" supplied with your TV. For the following TV users: KLV-32D300A, KLV-32V300A KLV-32M300A 1 Remove the screws from the rear of the TV. [. . . ] Be sure to confirm the completion of the installation for safety. · Be careful not to allow the cord and cables to get caught when removing the TV. · Be careful not to hurt your hands or fingers when removing the TV. WARNING Be sure that two or more persons hold the TV when carrying it. When removing the TV To Sony Dealers Specifications Unit: mm Weight: 4. 7 kg 1 2 Unplug the AC power cord from the wall outlet. [. . . ]