User manual SIM2 RTX 45
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SIM2 RTX 45. We hope that this SIM2 RTX 45 user guide will be useful to you.
Manual abstract: user guide SIM2 RTX 45
Detailed instructions for use are in the User's Guide.
[. . . ] RTX 45-55
USER AND INSTALLATION MANUAL
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
ELECTRIC SHOCK HAZARD DO NOT OPEN
!
For the DigiOptical Image Processor use exclusively the power supply unit provided or an alternative power supply unit expressly approved by SIM2. Position the power supply cables so that they do not constitute an obstruction. Position the power supply cables where they cannot be reached by children. Install the units as close as possible to the wall electrical socket outlet. [. . . ] The DigiOptical Image Processor sends commands to the Display and receives operating status information from the Display and function commands from the user. The system can be controlled from either the remote control (via the infrared sensors on the DigiOptical Image Processor and on the Display) or the keypad located on the top of the Display. The two units have separate power supplies however: after connecting the unit to the electrical mains supply, set the two power switches to "I"; the DigiOptical Image Processor power switch is located on the external power supply unit (Fig. will operate but it may be unable to read certain input signals correctly. Switching on the system: · from the remote control (keys 0-9) · from the Display keypad (keys and ). Pressing a key from 1-9 on the remote control selects the corresponding
MENU
ESC
AUTO
0
After a few seconds (system initialisation interval), the DigiOptical Image Processor and the Display assume stand-by mode. System status information is provided by two LEDs (green and blue) on the front panel of the DigiOptical Image Processor, a blue LED on the front of the Display, and the keypad status (off or illuminated). If the "No optical link" or "Error" signals are active the system cannot be operated; if the "Warning" signal is active the system Table 3
Status
DigiOptical Image Processor
Green LED Off Initialisation Stand-by On Cooling Optical link not active Caution Error : Off : On : Flashing Blue LED
I
O
Fig. 6b input; pressing 0 selects the input active at the time the system was last switched off. If the system is switched on very soon after it was last switched off, the lamp may fail to come on because it is too hot. Switching the system off : · from the remote control ( key) · from the Display keypad ( key). If you wish to power off the system completely, wait at least one minute in stand-by before setting the mains power switches on the units to the "O" position or disconnecting the power supply
Display
MENU
Front LED Keyboard pad
ESC
AUTO
-
-
-
-
- : Insignificant
10
Fig. This is to allow the fans in the Display unit sufficient time to cool the lamp.
KEYPAD
The keypad on the back of the Display features eight keys providing the facility for complete control of the apparatus even without the remote control.
MENU Activates the On Screen Display menus. (if pressed in the absence of the On Screen Display) calls the INFO information window
Switches system to stand-by.
MENU
ESC
AUTO
ESC Deactivates the On Screen Display AUTO Selects Auto Adjust (automatic optimisation of the displayed image).
Fig. 9
REMOTE CONTROL
The remote control transmits commands to the system by infrared signals. There are two infrared sensors, one at the front of the Display and one on the front panel of the DigiOptical Image Processor. Avoid placing obstructions between the remote control and the infrared sensor at the front of the projector; this will impair the remote control performance. Insert the batteries, taking care to match the polarity, as indicated in the battery compartment in the handset (Fig. Change the remote control batteries if you experience difficulty in transmitting commands to the system. Remove batteries from the remote control if it is to remain unused for a long period of time to avoid the risk of potentially harmful chemical leaks.
+ +
+ + -
Four 1. 5V AAA-type batteries
Fig. KEYS 0-9 Switch system on from stand-by and allow direct source selection. Navigate through the On Screen Display and make adjustments to the parameters. [. . . ] · Check that the power cables are correctly connected to the units' power sockets. · Check the condition of the fuse located on the power socket on the rear of the Display. · Replace the fuse located on the display power socket with an identical type (T 3. 15A H). · If the fuse blows repeatedly, seek technical assistance from your nearest Dealer. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SIM2 RTX 45
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SIM2 RTX 45 will begin.