User manual SHARP XL-HP505

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MICRO COMPONENT SYSTEM MODEL XL-HP505 Micro Component System consisting of XL-HP505 (main unit) and CP-HP505 (speaker system). XL-HP505 OPERATION MANUAL Accessories Please confirm that the following accessories are included. Remote control 1 AM loop antenna 1 (RRMCG0408AWSA) (QANTL0005AWZZ) FM antenna 1 (92LFANT1746A) Note: Only the above accessories are included. XL-HP505 SPECIAL NOTES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] The new tracks will be stored after the last track of the original program. To check which tracks are programmed: While the unit is stopped in the programmed play mode, press the or button. Notes: " When a disc with programmed tracks is ejected, the program is automatically canceled. " Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. " During programmed play, the CD DIRECT PLAY buttons will not work. 2 Press one of the 1 - 5 buttons to select the desired disc. CD Playback Selected disc number 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button. Press the / button to start playback. 6 7 20 Listening to the radio !Tuning XL-HP505 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). or ) button to tune in to the desired Notes: " When radio interference occurs, auto scan tuning may stop automatically at that point. To receive an FM stereo transmission Auto power on function: When you press any of the following buttons, the unit turns on. " TUNER (BAND) button (main unit and remote control): The unit turns on and the "TUNER" function is activated. " / button on the main unit: The unit turns on and playback of the last function starts (CD/TAPE/TUNER/VIDEO). Press the TUNER (BAND) button to display the "ST" indicator. " If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. FM stereo mode indicator FM stereo receiving indicator 21 Radio Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. XL-HP505 Listening to the radio (continued) !Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a button. To recall a memorized station Press the PRESET ( or lect the desired station. ) button for less than 0. 5 seconds to se- 1 2 Perform steps 1 - 3 in "Tuning" on page 21. Press the MEMORY/SET (MEMORY) button to enter the preset tuning saving mode. ! [. . . ] The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. XL-HP505 !General Power source Power consumption Dimensions AC 120 V, 60 Hz 80 W Width: 7-1/4" (185 mm) Height: 10-1/4" (260 mm) Depth: 12" (307 mm) 13. 7 lbs. Cassette deck Frequency response Signal/noise ratio Wow and flutter 50 - 14, 000 Hz (normal tape) 50 dB (recording/playback) 0. 3 % (WRMS) Weight ! [. . . ]