User manual SHARP XG-NV7XU

[. . . ] 25 Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) . . . . . . . . . . . . . 25 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) . . . . . . . . . . . . 26 Setting of Accept IP Address (ADVANCED[6]Accept IP Addr(1) ­ [8]Accept IP Addr(3)) . . . . . . . . . . . . . . . . 26 Accepting All IP Addresses (ADVANCED[9]Accept All IP Addr) . . . . . . . . . . . . [. . . ] On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). Setting the TCP port number used when exchanging data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Items SMTP Server Setting example / Remarks Setting an SMTP server address for e-mail transmission. e. g. 1 : 192. 168. 150. 253 e. g. 2 : smtp123. sharp. co. jp * When using a domain name, make settings for the DNS server. The name set here appears in the "Originator Name" column of the body of the message. Originator E-mail Address Originator Name Data Port Search Port Note · SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters. · You can input the characters below: SMTP Server and Originator E-mail Address : a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time for "Originator E-mail Address". ) Originator Name : a-z, A-Z, 0-9, -, _, (, ), space · If the settings of "3. Setting up a Network Connection for the Projector" on pages 11 and 12 are incorrectly set, e-mail will not be send. After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for 10 seconds and then re-access. · You can input the characters below : A-Z, 0-9, -, _, (, ), space (When "a-z" are input, they are converted to "A-Z" automatically. ) -16 Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail ­ Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support ­ Access URL) On this screen, you can input e-mail destinations to which error notification (error items) e-mails are sent. Items E-mail Address Description Set addresses to which error notification e-mail is sent. (Page 25) [5]Network Ping Test It is possible to confirm that a network connection between the projector and a computer etc. (Page 26) [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr (Factory default setting : Accept All) For improved security, it is possible to set up to three IP addresses allowing connection to the projector. (Page 26) [0] Search Port (Factory default setting : 5006) Setting the port number used when searching for the projector. (Page 27) [!] Restore Default Setting Restores all setting values that can be set using the menu to the default state. (Page 27) Note · When "DHCP Client" is set to "OFF" on the projector: IP address : 192. 168. 150. 2 Subnet mask : 255. 255. 255. 0 Default gateway : 0. 0. 0. 0 -20 Setting up the Projector Using RS-232C or Telnet Enter number or symbol of item to be selected on the SETUP MENU. Setting is carried out one item at a time, and saved at the end. View Setting Detail List ([V]View All Setting) SETUP MENU ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XX-XXXX Projector Name : XX-XXXX MAC Address : 08:00:1F:B1:B7:74 DHCP Client : Enabled IP Address : 192. 168. 150. 2 Subnet Mask : 255. 255. 255. 0 Default Gateway : Not Used RS-232 Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Auto Logout Time : 5 minutes Search Port : 5006 Set Items Example: When setting IP Address (change from 192. 168. 150. 2 to 192. 168. 150. 3) SETUP MENU ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>1 IP Address : 192. 168. 150. 2 Please Enter : 192. 168. 150. 3 (change) --> 192. 168. 150. 3 ---------------------------------SETUP MENU-------------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XX-XXXX Projector Name : XX-XXXX MAC Address : 08:00:1F:B1:B7:74 IP Address : 192. 168. 150. 3 Subnet Mask : 255. 255. 255. 0 Default Gateway : Not Used RS-232C Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Auto Logout Time : 5 minutes Search Port : 5006 1 1 *1 2 *2 * 3 1 Enter "v" and press the "Enter" key. Display all setting values(*). *3 1 Enter "1" (number of item to be set), and press the "Enter" key. 3 Enter "v" and press the "Enter" key to verify setting detail list. IP address is being changed (*3). Note · Verification of setting detail list can be omitted. · Setting details are not effective until they have been saved. (Page 22) · If an invalid number is entered, an error message ("Parameter Error!") will be displayed. [. . . ] \ Check that the power supply is turned on for the network device such as a hub between the projector and a computer. Check the network settings for the computer and the projector \ Check the following network settings for the projector. · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]