User manual SHARP XG-NV1E

[. . . ] 35 Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) . . . . . . . . . . . . . 35 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) . . . . . . . . . . . . 36 Setting of Accept IP Address (ADVANCED[6]Accept IP Addr(1) ­ [8]Accept IP Addr(3)) . . . . . . . . . . . . . 36 Accepting All IP Addresses (ADVANCED[9]Accept All IP Addr) . . . . . . . . . . . . [. . . ] No limits are set to IP addresses All IP Addresses connecting to the projector. From only For security improvement, only an specific IP IP address set by "Address 1-3" addresses can be connected to the projector. After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for 10 seconds and then re-access. · You can input the characters below : a-z, A-Z, 0-9, -, _ · To cancel User Name and Password, enter nothing and then press "Apply" button. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. · You cannot operate this page while the projector is warming up. · While the projector is in standby mode, you can only control "Power ON". · For details about each item, refer to the projector's operation manual. -25 Controlling the Projector via LAN Making General Settings for the Network (Network ­ General) Setting for Sending E-mail when an Error Occurs (Mail ­ Originator Settings) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). Setting the TCP port number used when exchanging a data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). (Page 33) [2]Subnet Mask (Factory default setting : 255. 255. 255. 0) Subnet mask settings. (Page 33) [3]Default Gateway (Factory default setting : Not Used) Default gateway settings. (Page 33) [4]User Name (Factory default setting : Not Required) Setting of user name for security protection. (Page 34) [5]Password (Factory default setting : Not Required) Setting of password for security protection. (Page 34) [6]RS-232C Baud Rate (Factory default setting : 9600 bps) Baud rate settings for the RS-232C terminals. (Page 34) [7]Projector Name (Factory default setting : XGPH50X) It is possible to assign a projector name. (Page 32) advanced> [1]Auto Logout Time (Factory default setting : 5 minutes) Setting of time until automatic disconnection of network connection. (Page 35) [2]Data Port (Factory default setting : 10002) Setting the TCP port number used when exchanging data. (Page 35) [5]Network Ping Test It is possible to confirm that a network connection between the projector and a computer etc. (Page 36) [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr (Factory default setting : Accept All) For improved security, it is possible to set up to three IP addresses allowing connection to the projector. (Page 36) [0] Search Port (Factory default setting : 5006) Setting the port number used when searching for the projector. [. . . ] · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]