User manual SHARP VC-D810S

[. . . ] G No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (UK) Limited. THIS MANUAL COVERS A RANGE OF MODELS. ALL OF THE FEATURES MENTIONED MAY NOT NECESSARILY APPLY TO YOUR VCR. (i) REMOTE CONTROL STANDBY 1. SV/V+/TIMER OPERATE INPUT SELECT TIMER ON/OFF MENU SV/V+ /TIMER AUDIO OUT TV CH VOL + 14. MENU SELECT CH SKIP SEARCH VOL ZERO BACK SET / CLEAR MODE OSD / / / 20. [. . . ] 12-hour clock am/pm can be selected using the AM/PM · · If button on the remote control. appears on the VCR display, press TIMER ON/OFF before starting. Check that the clock is displaying the correct time. SETTING A RECORDING For example: Recording a programme on channel 3 from 21:05 to 22:30 on July 9th. 1. The position which is initially highlighted is the next available timer record entry. Either: If this is the date you wish to make the recording on, press SET to confirm this. For example for July 9th, press 0 9 (9th), then 0 7 (July). 1/2 DA T E 21 / 06 9 / 07 --/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-SP ---SET : SE L ECT : ENT ER ME NU : E X I T 5. If you want to make additional recordings at the same time each day or week, use [K/L] or select D (daily) or W (weekly). Then press SET to confirm. DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D - -:--:---/-- --:--:---/-- --:--:-- 1/2 SP ---- 7. Then press SET to confirm. GB-11 BASIC OPERATION HOW TO SET A DELAYED RECORDING 8. Enter the start time using the [K/L] or the NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press SET to confirm. DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-1/2 SP SP --- 9. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 10. If you wish to change the RECORDING SPEED, use the [H/J] to highlight SP. In this case the VCR automatically switches to receive the mono signal. GB-14 ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers. EXISTING AERIAL CABLE BACK OF TELEVISION RF CONNECTION CABLE ANTENNA IN ENTREE AERIAL IN RF OUT SORTIE ANTENNE RF-OUT AUDIO OUT L and R + AUDIO PHONO LEADS (NOT SUPPLIED) AMPLIFIER GB-15 ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. Press DISPLAY on the remote control as many times as necessary until "R" appears on the VCR display. The tape remaining will be shown on the VCR display in hours and minutes. For example: In Standard Play, 1 hour 23 minutes is left on the tape: In Long Play, 2 hours 46 minutes is left on the tape: In Extended Play, 4 hours 9 minutes is left on the tape: NOTES: · · Do not interrupt the tape remaining calculation. If less than 5 minutes of tape remains the display will flash. PLAYING BACK A VIDEO TAPE REPEATEDLY You can set your VCR to automatically rewind at the end of playing a video tape and replay the entire tape again. Press MENU to display the main menu on the screen. MODE MENU SCREEN B L U E MU T E R E P E A T AU T O ON OF F OF F 2. Press MENU to return to normal screen. GB-16 SET : SE L ECT : ENT ER : CHANGE ME NU : E X I T ADVANCED OPERATION LCD DISPLAY TIME OF DAY Shows current time of day, if the clock is set. For example, 21:20 appears: CHANNEL STATUS Shows the current VCR channel preset. [. . . ] (SP); Frequency response: 20 Hz - 20 kHz; Wow and flutter: < 0. 005% Wrm (JIS A) 360(W) x 289(D) x 93(H) mm 3. 2 kg (approx. ) 75 RF Connection cable, operation manual, remote control, AA/R6/UM3 battery (x2) Tape width: Tape speed: Antenna: Reception channels: RF output signal: Power requirement: Power consumption: Operating temperature: Storage temperature: Video input: Video output: Audio input: Audio output: Hi-Fi audio: Dimensions: Weight: Supplied accessories: · · Specifications are subject to change without notice as part of our policy of continuous improvement. No liability is accepted for any inaccuracies or omissions in this publication, although every possible care has been taken to make it complete and as accurate as possible. GB-29 MORE INFORMATION ABOUT YOUR VCR TROUBLESHOOTING AREA INSTALLATION PROBLEM TV will not tune in to the VCR. POSSIBLE CAUSE/CURE · Check all the cables are correctly connected. (Refer to VCR Reset at the back of the book. ) Auto Installation screen does not appear when the VCR is switched on OR Auto Installation is POWER not complete. · Make sure the wall socket has power (plug another appliance in). [. . . ]