User manual SHARP QT-272H

[. . . ] Lorsque le commutateur ON/STAND-BY est mise en , l'appareil est toujours sous tension. Lorsque le commutateur ON/STAND-BY se trouve sur la position ON, l'appareil est prt fonctionner par la tlcommande. Avertissement: Cet appareil contient des pices non rparables par l'utilisateur. L'appareil contenant des organes ports haute tension, dbrancher l'appareil avant toute rparation ou en priode de non-utilisation. [. . . ] This will prevent potential damage due to battery leakage. " Test of the remote control The remote control can be used within the range shown below: Press the ON/STAND-BY button. Incorrect installation may cause the unit to malfunction. Notes concerning use: !Replace the batteries if the operating distance is reduced or if the operation becomes erratic. Purchase 2 "AAA" size batteries (UM-4, R03, HP-16 or similar). Periodically clean the transmitter on the remote control and the sensor on the unit with a soft cloth. Exposing the sensor on the unit to strong light may interfere with operation. Keep the remote control away from moisture, heat, shock, and vibrations. N Remote sensor 0. 2 m - 6 m P E E-10 04/6/14 QT-272H_SEEG_E2. fm 9HX80432100007 QT-272H Setting the clock 4 Within 5 seconds, press the to adjust the hour. Hold it down to advance continuously. ENGLISH 5 6 Within 5 seconds, press the lect the minute. Within 5 seconds, press the to adjust the minute. button to se- or button Preparation for Use Press the or button once to advance the time by 1 minute. Hold it down to advance continuously. 7 - Setting the clock - Within 5 seconds, press the ENTER button. To confirm the time display: Press the CLOCK button for less than 0. 5 seconds whilst the main unit turns the power on. The time display will appear for about 5 seconds. To readjust the clock: Perform "Setting the clock" from step 1. To change the 12-hour or 24-hour display: The clock can only be set using the buttons on the remote control. During an operation, " " may appear indicating that the operation is disabled. P Play PLAY Pause PAUSE E E-14 04/6/14 QT-272H_SEEG_E3. fm 9HX80432100007 QT-272H Basic operation Some of these functions are only available on the remote control. ENGLISH " Fast forward/Fast reverse (search) You can search the desired point as you play the disc. 1 Whilst a disc is playing, press the Example: When the button is pressed or button. FF 2 X PLAY (Normal play) 2X 4X 6X 8X DVD Operation The disc is forwarded by the button and reversed by the button. 7 2 - Basic operation - Press the PLAY/PAUSE / button to return to normal playback. " To locate the beginning of a chapter/track (skip) You can skip the current chapter (track) to the next or previous. Notes: !Sound output and the appearance of subtitles differ depending on the disc. When search is performed during the DVD playback, pictures may not be forwarded or reversed in the search speed specified in this manual, depending on the disc or the scene being played. Whilst a disc is playing, press the or button. SHARP 9HX80432100007 !Press the button to skip to the beginning of the current chapter (track). Press the button again to skip to the beginning of the previous chapter (track). Notes: !Some discs do not display the chapter (track) and the skip feature is disabled. to off (see page 21). E-15 04/6/14 QT-272H_SEEG_E3. fm 9HX80432100007 Useful operation " To start playback from the desired point (direct play) To select and play the desired title and chapter: Some of these functions are only available on the remote control. QT-272H ENGLISH D " Still picture/Frame advance You can freeze the image and advance frame by frame. 1 In the playback mode, press the GOTO button. TV screen 1 2 3 Whilst a disc is playing, press the STEP Playback is paused. or button. F TITLE 01/02 CHAPTER 001/002 Each press of the STEP The or button advances the frame. 2 Within 10 seconds, select the title or chapter by pressing the or button and enter the title or chapter number using the direct number buttons. If the track number is 2 digits or more, press "+10" and enter the number. Example: To select chapter 12, press "+10" and "2". To select chapter 22, press "+10", "+10" and "2". button does not allow you to operate this function on SVCD/VCD. Press the PLAY/PAUSE / button to return to normal playback. S - Basic operation / Useful operation - Note: Still and frame advance features are disabled on some discs. DVD Operation " Slow-motion play You can slow down the playback speed. 8 V 3 Within 10 seconds, press the ENTER button. 1 Notes: Whilst a disc is playing, press the SLOW or button. SF 2X !With DVDs, you can specify the desired point only in the current title and not in another title. To play by specifying time (time search): You can play back from the desired point by specifying the time. Each time the button is pressed, the speed of slow-motion play changes in the following sequence. DVD: SVCD/VCD: I SF 2 SF 4 SF 6 / SR 2 / SR 4 / SR 6 / SR 8 SF 2 SF 4 SF 6 SF 8 Play 1 SHARP 9HX80432100007 In the playback mode, press the GOTO button twice. TITLE 02/12 TIME __ : __ : __ or button repeatedly. N If the "_ _:_ _:_ _" is not highlighted, press the SF 8 Play 2 Within 10 seconds, specify the time with the direct number buttons, and then press the ENTER button. TITLE 02/12 TIME 01:23:40 2 P Press the PLAY/PAUSE / button to return to normal playback. ! [. . . ] If something is wrong with this product, check the following before calling your authorised SHARP dealer or service centre. QT-272H " DVD player Symptom Possible cause Reference page Even though a disc is loaded, !Is a disc other than a DVD (region number 2 or ALL), SVCD, VCD, audio CD, CD-R or CD-RW loaded? ENGLISH D " General Symptom No sound is heard. Check that the correct video input is selected on the TV. - Troubleshooting chart - P. 6 The unit does not operate even if the power is on. References V Image cannot be played back. [. . . ]