User manual SHARP QT-250H

[. . . ] q This unit should only be used within the range of 5°C - 35°C (41°F - 95°F). q The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. q No naked flame sources, such as lighted candles, should be placed on the apparatus. q Attention should be drawn to the environmental aspects of battery disposal. [. . . ] Selector adjustment: Slide the selector with a screwdriver to the appropriate voltage number. (AC 110 - 127 V or AC 220 - 240 V) Notes: q If the unit will not be used for a long period of time, remove the AC power lead from the AC socket. q Connection of the AC power lead to the unit disconnects the batteries. Using other power leads may cause an electric shock or fire. Operation with Batteries 3 4 2 1 5 6 8 7 1 Disconnect the AC power lead, and remove the battery compartment cover. 2 Insert 8 "D" size batteries (UM/SUM-1, R20, HP-2 or similar) into the battery compartment. q Insert the batteries according to the direction indicated on the rear panel. q When inserting or removing the batteries, push them toward the ë battery terminals. q Installing the batteries incorrectly may cause the unit to malfunction. 3 Replace the battery compartment cover. Battery replacement: Replace the batteries when they become weak and/or recording or playback is impaired. q Remove the batteries if they are weak or if the unit will not be used for long periods of time. Caution: Do not use rechargeable batteries (nickel-cadmium battery, etc. ). E-3 01-E1-E9-QT-250H(S) 4 01. 9. 19, 15:28 Sound Control Volume Turn the VOLUME control to increase or decrease the volume. Extra bass (X-BASS) Press the X-BASS button to emphasise bass sound. Listening to the Radio 1 2 3 4 Set the FUNCTION switch to RADIO. not in stereo. s Erasing a recorded tape 1 Set the FUNCTION switch to LINE. q Do not connect anything to the LINE IN and MIXING MIC sockets. 2 Load a tape into the cassette compartment with the side to be erased facing up. 3 Press the RECORD q button. E-6 01-E1-E9-QT-250H(S) 7 01. 9. 19, 15:28 Mixing from a Microphone , , s Mixing from a microphone s Recording of mixed sound and other sources to a cassette tape You can listen to mixed sound from an external microphone and other sources. You can record mixed sound from an external microphone and other sources. 1 2 3 4 To protect the speakers from shock noise and to avoid disturbing noises, set the VOLUME control to minimum. Set the FUNCTION switch to the desired source (cassette, radio or external unit) and play it back. 1 2 3 4 5 6 To protect the speakers from shock noise and to avoid disturbing noises, set the VOLUME control to minimum. Load a cassette into the cassette compartment. Adjust the volume of the audio source and the microphone using the VOLUME control. Notes: q Be sure that the microphone has a 3. 5 mm (1/8") diameter plug, and is of 600 ohms impedance. q Place the microphone about 10 - 15 cm (46") away from the source. q If howling occurs, lower the volume or move the microphone as far as possible from the speakers. Caution: When not using the microphone, remove the microphone plug from the MIXING MIC socket. Set the FUNCTION switch to RADIO or LINE. q Mixing recording is not possible if the FUNCTION switch is set to TAPE. [. . . ] (red ¡ right channel, white ¡ left channel) Set the FUNCTION switch to LINE. Play the CD player etc. Notes: q To prevent noise and interference when using the tuner, turn off the power to your CD player. q To prevent hum interference, do not place this unit near television receivers. phones, make sure the volume level is reduced. q Be sure your headphones have a 3. 5 mm (1/8") diameter plug and are between 16 ohms and 50 ohms impedance. [. . . ]