User manual SHARP PN-ZT10E

[. . . ] ENGLISH PN-ZT10E 65" Touch Panel OPERATION MANUAL DEUTSCH FRANÇAIS Applicable models (as of March 2007) LCD MONITOR PN-655E Authorised representative responsible for the European Union Community Market SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT: To aid reporting in case of loss or theft, please record the product's model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No. : Serial No. : WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] 1. 8 m) Batteries for touch pen (R-03 ["AAA" size] x 2) Mounting bracket (5) Mounting screw (10) Operation manual (this manual): 1 Utility Disk (CD-ROM): 1 TouchPanel driver/TouchPanel Setting Program Blank sticker: 1 Place a blank sticker onto the SHARP logo to cover the logo. · For environmental protection!Follow the disposal instructions for your area. Operating requirements PC OS PC/AT compatible featuring a USB port (A CD-ROM drive is required for programme installation. ) Windows XP (Service Pack 1 or later is recommended) 7 E Part Names Touch panel Infrared transmitter/receiver Back of the right side USB terminal Pen switch Set this switch to OFF during normal use. (When set to ON, the switch illuminates in green. ) Infrared transmitter/receiver Touch pen signal receiver Caution · The touch pen signal receiver is protruded. Also note that if this section is covered with something, the touch pen does not operate properly. Touch pen Function switch Pen tip Infrared transmitter E 8 Preparation Mounting the touch panel Caution · Consult your dealer about mounting the touch panel. Mounting the unit should not be conducted by the customer on their own. · Do not mount a touch panel to the monitor other than the applicable model. · Mount the touch panel to the monitor after mounting the monitor to the stand or other mountings. Do not try to mount the touch panel by placing the unit on the floor and then placing the monitor over it. This may cause damage or a malfunction. · Check that the clearance between the monitor and the touch panel is not too great. 1. Attach the mounting brackets (supplied) at the two positions on the rear of the touch panel for initial fixing. Attach the mounting brackets in the orientation shown in the illustration. During the initial fixing, secure the brackets so that they are raised at the highest position. Touch panel (rear side) Mounting bracket (supplied) Touch panel (rear side) Mounting screws (supplied) 2. Be careful that the touch panel does not hit the monitor. 9 E Preparation (Continued) 3. Lower the mounting brackets from the initial position in step 1 and secure them with screws (2 brackets). 4. Attach the remaining mounting brackets (3 brackets). Caution · Tighten the mounting screws securely using a flat-blade screwdriver. This may cause distortion of the unit. E 10 Setting up the PC To use the touch panel, you need to connect a PC to the touch panel and install the TouchPanel driver and TouchPanel Setting Program onto the PC. Installing the TouchPanel driver Caution · This procedure requires administrator privilege. It will be detected as a failure of the infrared transmitter/receiver elements, leading to a malfunction. When this occurs, disconnect the USB cable once and then reconnect it. 1. Connect the PC and touch panel with the USB cable (supplied). To the USB terminal of the PC USB terminal To the USB terminal USB cable (supplied) When the cable is connected, the "Welcome to the Found New Hardware Wizard" screen is displayed. If the message "Can Windows connect to Windows Update to search for software?" appears, select "No, not this time" and click "Next". Select "Install the software automatically" and click "Next". If the message "has not passed Windows Logo testing to verify its compatibility. . . " appears, click "Continue Anyway". [. . . ] (2) Click "OK". 17 E Deleting (Uninstalling) the Programme Caution · This procedure requires administrator privilege. Deleting the TouchPanel Setting Program 1. Click the "start" button, select "All Programs", "Startup", and then right-click "tpdrv". Click the "start" button, select "Control Panel", and then click "Add or Remove Programs". When you use the Classic View, double-click "Add or Remove Programs". [. . . ]