User manual SHARP PN-L702B

[. . . ] This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] When the main power switch is off, the monitor is not turned on with the POWER button on the remote control unit. Turning power on/off using remote control remote control unit Press the POWER button to turn the power ON/OFF. Power LED When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. When the input mode (see page 22) is set to "DIGITAL" or "ANALOG" and there is no video signal input, the backlight of the monitor is turned off and the monitor enters input signal waiting mode. ) If the monitor is in this mode and you press the POWER button on the remote control unit, the monitor enters standby mode. If the remote control is not available, you can turn on/off by pressing the power switch power LED with a sharp object (see page 8). INPUT (Input mode selection) Each time you press this button, the mode changes in the following order (see page 8): · dIGITAL ANALOG COMPONENT VIDEO DIGITAL. * If the remote control is not available, you can change the mode by pressing the input switch on the front panel of the monitor with a sharp object (see page 8). Press the MUTE button again to turn the sound back to the previous level. * If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears. * If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears. default Center [OSD V-POSITION] Function Adjusts the vertical display position of menu screen. SET] Function Assigns ID numbers to monitors connected in a daisy chain (see page 38), using RS-232C cables. Adjustable range 0 - 255 Default 0 Note The numbers 1 to 255 are available for ID numbers. (If "0" is set, the system regards this as the state where no ID number is set. ) Although numbers up to 255 can be used for monitor IDs, the number of connectable monitors varies depending on the length of RS-232C cables and the installation environment. Adjustable range 0 - 15 Default 0 (Increasing the value makes the sub screen more transparent. If the main screen is displayed as a full screen by the AUTO OFF function, the sound for the main screen is output even when the sound for the sub screen is specified. Adjustable range PC/AV [MAIN POS] Specifies whether to display the main screen on the right or left in PbyP or PbyP2 mode. function Adjustable range LEFT/RIGHT Default LEFT [PbyP2 POS] Function Sets the vertical position of the sub screen in PbyP2 mode. Adjustable range TOP/CENTER/BOTTOM Default CENTER [AUTO OFF] Function Sets whether to display the main screen as a full screen in PIP, PbyP, or PbyP2 mode when there is no signal input for the sub screen. Set this function with "PIP MODES" in the MODE SELECT 3 menu. [. . . ] ) W When the "Parameter" is set in the parameter field (see page 39), the command functions as described under "Control/Response Contents". R The returned value indicated under "Reply" can be obtained by setting "?* "Yes" indicates commands which can be used in power standby mode. ENLARGE OFF 2x2 3x3 4x4 Width of the right/left bezel Height of the upper/lower bezel SETTING: 2 x 2) UPPER LEFT SETTING: 2 x 2) UPPER RIGHT SETTING: 2 x 2) LOWER LEFT SETTING: 2 x 2) LOWER RIGHT SETTING: 3 x 3) UPPER LEFT SETTING: 3 x 3) UPPER MIDDLE SETTING: 3 x 3) UPPER RIGHT SETTING: 3 x 3) MIDDLE LEFT SETTING: 3 x 3) CENTER SETTING: 3 x 3) MIDDLE RIGHT SETTING: 3 x 3) LOWER LEFT SETTING: 3 x 3) LOWER MIDDLE SETTING: 3 x 3) LOWER RIGHT SETTING: 4 x 4) Leftmost segment in the first row from the top SETTING: 4 x 4) Middle left segment in the first row from the top SETTING: 4 x 4) Middle right segment in the first row from the top SETTING: 4 x 4) Rightmost segment in the first row from the top SETTING: 4 x 4) Leftmost segment in the second row from the top SETTING: 4 x 4) Middle left segment in the second row from the top SETTING: 4 x 4) Middle right segment in the second row from the top SETTING: 4 x 4) Rightmost segment in the second row from the top SETTING: 4 x 4) Leftmost segment in the third row from the top SETTING: 4 x 4) Middle left segment in the third row from the top SETTING: 4 x 4) Middle right segment in the third row from the top SETTING: 4 x 4) Rightmost segment in the third row from the top SETTING: 4 x 4) Leftmost segment in the forth row from the top SETTING: 4 x 4) Middle left segment in the forth row from the top SETTING: 4 x 4) Middle right segment in the forth row from the top SETTING: 4 x 4) Rightmost segment in the forth row from the top No No Yes Control/Response contents * SETTING: 3 x 3) UPPER LEFT SETTING: 3 x 3) UPPER MIDDLE SETTING: 3 x 3) UPPER RIGHT SETTING: 3 x 3) MIDDLE LEFT SETTING: 3 x 3) CENTER SETTING: 3 x 3) MIDDLE RIGHT SETTING: 3 x 3) LOWER LEFT SETTING: 3 x 3) LOWER MIDDLE SETTING: 3 x 3) LOWER RIGHT SETTING: 4 x 4) Leftmost segment in the first row from the top SETTING: 4 x 4) Middle left segment in the first row from the top SETTING: 4 x 4) Middle right segment in the first row from the top SETTING: 4 x 4) Rightmost segment in the first row from the top SETTING: 4 x 4) Leftmost segment in the second row from the top SETTING: 4 x 4) Middle left segment in the second row from the top SETTING: 4 x 4) Middle right segment in the second row from the top SETTING: 4 x 4) Rightmost segment in the second row from the top SETTING: 4 x 4) Leftmost segment in the third row from the top SETTING: 4 x 4) Middle left segment in the third row from the top SETTING: 4 x 4) Middle right segment in the third row from the top SETTING: 4 x 4) Rightmost segment in the third row from the top SETTING: 4 x 4) Leftmost segment in the forth row from the top SETTING: 4 x 4) Middle left segment in the forth row from the top SETTING: 4 x 4) Middle right segment in the forth row from the top SETTING: 4 x 4) Rightmost segment in the forth row from the top WIDE NORMAL Dot by Dot ZOOM 1 ZOOM 2 This ID number is only effective for the command immediately after this command. [. . . ]