User manual SHARP PG-D120U

[. . . ] In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: WARNING: THIS APPARATUS MUST BE EARTHED. [. . . ] · If you do not want to display the Setup Guide for the next time, set "Menu" - "SCR - ADJ" "Setup Guide" to "Off". (See page 49. ) * The PG-D120U model is not equipped with the ZOOM function. Basic Operation Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. · Using the knob on the focus ring will make the adjustments easier. PG-D120U Focus ring 27 Image Projection (Continued) 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. Make small adjustments. HEIGHT ADJUST lever 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed. Rear adjustment foot 3 Use the rear adjustment foot to make the projector level. · The projector is adjustable ±2 degrees from the standard position. Info · Do not apply too much pressure on the projector when the front adjustment foot comes out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. · Do not hold by the lens area. Note · When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See pages 29 and 47. ) 3 Adjusting the Picture Size (except PG-D120U) You can adjust the picture size using the zoom ring on the projector. Rotate the zoom ring to enlarge or shrink the picture size. · Using the knob on the zoom ring will make the adjustments easier. Zoom ring 28 Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Note · The Keystone Correction can be adjusted up to an angle of approximately ±40 (PG-D3550W/ D3050W)/±25 (PG-D120U) degrees and the screen can also be set up to an angle of approximately ±40 (PG-D3550W/D3050W)/ ±25 (PG-D120U) degrees (When the Resize mode is set to "NORMAL" (see page 31)). Adjustment buttons (P/R/O/Q) RETURN button KEYSTONE button 1 On-screen display (Keystone Correction mode) KEYSTONE ADJUST 0 END Press KEYSTONE to enter the Keystone Correction mode. Shrinks upper side. - When the input signal resolution and refresh rate (vertical frequency) change. - When the Resize mode is changed. Note · See page 42 for details on the Picture mode. * "sRGB" is displayed only when RGB signal is input. 34 Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver. Connecting with a USB cable Computer To USB terminal To USB terminal or Remote receiver (optional, AN-MR2) USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ) The mouse pointer can be operated in the following way after it is connected. When moving the cursor When left-clicking Press L-CLICK. Press MOUSE/Adjustment buttons (P/R/O/Q). PAGE UP/ PAGE DOWN buttons MOUSE/Adjustment buttons ( / / / ) When right-clicking Press R-CLICK. R-CLICK button When your computer supports only a one-click mouse (such as Macintosh) Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function. Useful Features L-CLICK button When using [Page Up] or [Page Down] Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN. Note · This function only works with the Microsoft® Windows® OS and Mac OS® that support USB. · You cannot use this function when displaying the menu screen. · Confirm that the computer recognizes the USB connection. 35 Menu Items The following shows the items that can be set in the projector. "Quick Start Menu" Main menu Quick Start Menu Input Search Start "Picture" menu Sub menu Main menu Picture Picture Mode Sub menu Page 40 Resolution Page 42 Page 42 Standard Presentation Movie Game sRGB *3 Page 40 Resize Page 40 Keystone -80 -50 +80 *1 +50 *2 Normal Full Native Area Zoom V-Stretch 16:9 Contrast Bright Color Tint Sharp Red Blue -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 *4 +30 *4 +30 *4 +30 +30 Page 40 Eco + Quiet [On/Off] Page 43 English Deutsch Español Nederlands Français Italiano Svenska Português polski Magyar Türkçe Page 40 Language Page 40 CLR Temp -1 1 Page 43 BrilliantColorTM 0 2 Page 43 C. M. S. Setting [On/Off] Information Page 40 Go To Complete Menu Page 43 C. M. S. Page 40 *1 Adjustment range for PG-D3550W/D3050W. [. . . ] Picture is green on COMPUTER (YPbPr)/ HDMI (YPbPr) Picture is pink (no green) on COMPUTER (RGB)/ HDMI (RGB) Picture is too bright and whitish. 43 8, 9 57, 58, 59 58, 61, 62 26, 30 Page 58 45 The cooling fan becomes · When temperature inside the projector increases, the cooling fan runs faster. · Operate the remote control while pointing it at the projector's remote control sensor. · If direct sunlight or a strong fluorescent lamp is shining on the projector's remote control sensor, place the projector where it will not be affected by strong light. [. . . ]