User manual SHARP PG-M10X/S

[. . . ] ENGLISH OPERATION MANUAL MODEL PG-M10X PG-M10S FRANÇAIS DEUTSCH ITALIANO ESPAÑOL DIGITAL MULTIMEDIA PROJECTOR This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG. [. . . ] In such case, replace the lamp housing, then use the following procedure to reset. 1 2 Connect the power cord (page 18). Standby status will be activated. Press the INPUT SELECT and AUTO SYNC buttons of the main unit at the same time for 5 sec. After resetting, the STATUS indicator (page 36) that turned on because 1100 hours had been exceeded will turn off. Menu Operation The lamp hours of usage will be displayed on the screen when it has exceeded 1000 hours. To close the menu Press the R-CLICK/UNDO button. 29 Advanced Menu Settings Set the colors as desired in accordance with the image contents. Subtle color settings are possible, as desired. Setting is possible for each input. Setting the Video Type 1 2 3 1 2 3 4 Select the image to be input (page 20). With the FLIP COVER of the remote control open, press the MENU button to display the Advanced menu, then use the cursor / keys to select "COLOR". / keys to select With the FLIP COVER of the remote control open, press the MENU button to display the Advanced menu, then use the cursor / keys to select "COLOR". / keys to select "VIDEO / keys to set the "VIDEO The following can be selected. G DVD G VCR DVD is used for DVD players and Video is used for normal video players. / keys to set the The following can be selected. G Normal G Natural G Real G Custom Normal is standard settings; Natural stresses coloring; Real stresses brightness. Custom is used to adjust freely as desired. Selecting the Color System The following color systems can be used with this unit. G NTSC G NTSC 4. 43 G PAL G PAL-M G PAL-N G PAL60 G SECAM · Only "NTSC" and "PAL" can be used for component video. · "AUTO" cannot be set for PAL-M and PAL-N input signals. Select "PAL-M" or "PAL-N" in "COLOR SYSTEM" menu for PAL-M and PAL-N input signals. 5 Use the cursor / keys to select "CUSTOM", press the ENTER button to display the sub-menu and then set the gamma value. There are 33 index values. Menu Operation Adjusting Color Balance Color balance (white balance) can be set for each input. 1 2 3 4 Select an input for the color system to be selected (page 20). With the FLIP COVER of the remote control open, press the MENU button to display the Advanced menu, then use the cursor / keys to select "COLOR". Use the cursor / keys to select "COLOR SYSTEM" and then press the ENTER button. Use the cursor / keys to select the desired color system. 1 2 3 4 Select the image to be input (page 20). With the FLIP COVER of the remote control open, press the MENU button to display the Advanced menu, then use the cursor / keys to select "COLOR". keys to select keys to select the Four different types of color balance can be set beforehand: Low, Middle, Normal and High. When the ENTER button is pressed, the submenu will be displayed to enable fine adjustment. To close the menu Press the R-CLICK/UNDO button. 30 Setting in Accordance With Image Content Advanced Menu Settings (continued) Setting the Display Frame The display frame can be set individually for each input. Setting the COMPUTER input terminal The COMPUTER input terminal can be switched and used as the component video signal (YPBPR) input terminal. 1 2 3 4 Select the input for image selection (page 20). With the FLIP COVER of the remote control open, press the MENU button to display the Advanced menu, then use the cursor / keys to select "VIEW". Display the frame, then use the cursor / keys to select "ASPECT". [. . . ] 34 P Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 18, 20 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 18, 20 R Rear adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Rear projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]