User manual SHARP PG-F317-212X

[. . . ] 27 Setting Auto Logout Time (ADVANCED[1]Auto Logout Time) . . . . . . . . . . . . . 27 Carrying out Network Ping Test (ADVANCED[5]Network Ping Test) . . . . . . . . . . . . 28 Setting of Accept IP Address (ADVANCED[6]Accept IP Addr(1) ­ [8]Accept IP Addr(3)) . . . . . . . . . . . . . . . . 28 Accepting All IP Addresses (ADVANCED[9]Accept All IP Addr) . . . . . . . . . . . . [. . . ] Accept IP It is possible to set up to three Address IP addresses allowing connection to the projector. All IP No limits are set to IP addresses Addresses connecting to the projector. From only For security improvement, only an specific IP IP address set by "Address 1-3" addresses can be connected to the projector. Note · If you click the "Refresh" button before the screen is displayed completely, an error message ("Server Busy Error") will be displayed. · You cannot operate this page while the projector is warming up. · For details about each item, refer to the projector's operation manual. Note · User Name and Password can be up to 8 characters. · You can input the characters below : a-z, A-Z, 0-9, -, _ -17 Controlling the Projector via LAN Making General Settings for the Network (Network General) Setting for Sending E-mail when an Error Occurs (Mail ­ Originator Settings) On this screen, you can make settings for sending e-mail to report when the projector has generated an error. On this screen, you can make general settings relating to the network. Items Projector Name Auto Logout Time Description Setting the projector name. Setting the time interval in which the projector will be automatically disconnected from the network in units of a minute (from 1 to 65535 minutes). Setting the TCP port number used when exchanging data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). Items SMTP Server Setting example / Remarks Setting an SMTP server address for e-mail transmission. (Page 25) [4]User Name (Factory default setting : Not Required) Setting of user name for security protection. (Page 25) [5]Password (Factory default setting : Not Required) Setting of password for security protection. (Page 26) [6]RS-232C Baud Rate (Factory default setting : 9600 bps) Baud rate settings for the RS-232C terminals. (Page 26) [7]Projector Name It is possible to assign a projector name. (Page 24) advanced> [1]Auto Logout Time (Factory default setting : 5 minutes) Setting of time until automatic disconnection of network connection. (Page 27) [2]Data Port (Factory default setting : 10002) Setting the TCP port number used when exchanging data. (Page 27) [5]Network Ping Test It is possible to confirm that a network connection between the projector and a computer etc. (Page 28) [6]Accept IP Addr(1) [7]Accept IP Addr(2) [8]Accept IP Addr(3) [9]Accept All IP Addr (Factory default setting : Accept All) For improved security, it is possible to set up to three IP addresses allowing connection to the projector. (Page 28) [0] Search Port (Factory default setting : 5006) Setting the port number used when searching for the projector. (Page 29) [!] Restore Default Setting Restores all setting values that can be set using the menu to the default state. (Page 29) Note · When "DHCP Client" is set to "OFF" on the projector: IP address : 192. 168. 150. 2 Subnet mask : 255. 255. 255. 0 Default gateway : 0. 0. 0. 0 -22 Setting up the Projector Using RS-232C or Telnet Enter number or symbol of item to be selected on the SETUP MENU. [. . . ] \ Check that the power supply is turned on for the network device such as a hub between the projector and a computer. Check the network settings for the computer and the projector \ Check the following network settings for the projector. · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]