User manual SHARP PG-D40W3D

[. . . ] In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: WARNING: THIS APPARATUS MUST BE EARTHED. [. . . ] This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. · If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection. To cancel the keycode setting, input the keycode that you have already set. See page 51 for details. STANDBY button ON button On-screen display (confirmation message) Turning the Power Off (Putting the Projector into Standby Mode) Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into Standby mode. · The projector cannot be turned on while cooling. Info · Direct Power Off function: You can unplug the power cord from the AC outlet even if the cooling fan is still running. 26 Image Projection Setup Guide screen About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note · The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 4 ENTER 2 HEIGHT ADJUST 3 ZOOM ENTER button However, you can adjust the focus or height (angle) regardless of the highlighted item. · If you do not want to display the Setup Guide for the next time, set "Menu" - "SCR - ADJ" "Setup Guide" to "Off". (See page 49. ) Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. · Using the knob on the focus ring will make the adjustments easier. Basic Operation Focus ring 27 Image Projection (Continued) 2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. Make small adjustments. HEIGHT ADJUST lever 2 Remove your hands from the HEIGHT ADJUST lever of the projector after its height has been finely adjusted. · The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed. Rear adjustment foot 3 Use the rear adjustment foot to make the projector level. · The projector is adjustable ±2 degrees from the standard position. Info · Do not apply too much pressure on the projector when the front adjustment foot comes out. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. · Do not hold by the lens area. Note · When adjusting the height of the projector, trapezoidal distortion occurs. This is helpful when providing more detailed explanations. 1 Press MAGNIFY on the remote control. · Enlarges the image. · Pressing or MAGNIFY enlarges or reduces the projected image. Note Press . ×3 ×4 Freezing a Moving Image ×1 ×2 Press . 1 2 Press FREEZE. · The projected image is frozen. · You can change the location of the enlarged image using P, R, O and Q. Press FREEZE again to return to the moving image from the currently connected device. 2 Press RETURN on the remote control to cancel the operation. · The magnification then returns to ×1. Note Selecting the Picture Mode You can select the appropriate Picture mode for the projected image, such as movie or video game. Press PICTURE MODE. · When pressing PICTURE MODE, the Picture mode changes in the following order: STANDARD PRESENTATION MOVIE GAME sRGB* · The selectable magnifications differ depending on the input signal. · In the following cases, the image will return to the normal size (×1). - When the input signal resolution and refresh rate (vertical frequency) change. - When the Resize mode is changed. Note · See page 42 for details on the Picture mode. * "sRGB" is displayed only when RGB signal is input. 34 Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver. Connecting with a USB cable Computer To USB terminal To USB terminal or Remote receiver (optional, AN-MR2) USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ) The mouse pointer can be operated in the following way after it is connected. When moving the cursor When left-clicking Press L-CLICK. Press MOUSE/Adjustment buttons (P/R/O/Q). PAGE UP/ PAGE DOWN buttons MOUSE/Adjustment buttons ( / / / ) When right-clicking Press R-CLICK. R-CLICK button When your computer supports only a one-click mouse (such as Macintosh) Press L-CLICK or R-CLICK. Press PAGE UP or PAGE DOWN. Useful Features L-CLICK button When using [Page Up] or [Page Down] Note · This function only works with the Microsoft® Windows® OS and Mac OS® that support USB. · You cannot use this function when displaying the menu screen. [. . . ] the cabinet. Appendix 65 Troubleshooting (Continued) Problem Check Maintenance indicator on · See "Maintenance Indicators". Picture is green on COMPUTER (Component) Picture is pink (no green) on COMPUTER (RGB) Picture is too bright and whitish. 43 8, 9 57, 58, 59 58, 61, 62 26, 30 Page 58 45 The cooling fan becomes · When temperature inside the projector increases, the cooling fan runs faster. · Operate the remote control while pointing it at the projector's remote control sensor. [. . . ]