User manual SHARP PG-C45S

[. . . ] Introduction Connections and Setup Basic Operation Easy to Use Functions Appendix OPERATION MANUAL PG-C45S MODEL LCD PROJECTOR IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 14. Model No. : PG-C45S Serial No. : This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] However, for some signals, the optimal resolution mode in "Special Modes" on the "Fine Sync" menu screen may need to be selected to match the computer display mode. Basic Operation Set the resolution by selecting "Special Modes" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see. ) · When a DVD player or Digital Video is connected, select 480P as the input signal. · See "Checking the Input Signal" below for information on the currently selected input signal. Checking the Input Signal This function allows you to check the current input signal information. Select "Signal Info" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digital Video. -49 Adjusting Computer Images Auto Sync Adjustment Used to automatically adjust a computer image. Select "Auto Sync" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note When setting to " Normal" or " High Speed": · Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a computer. Manual adjustments should be performed: · When the optimum image cannot be achieved with Auto Sync adjustment. · Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. · When setting "Auto Sync" to "OFF" or is pressed Auto "High Speed", and if Sync will be executed in "High Speed" mode. If the button is pressed again within one minute, Auto Sync will be executed in "Normal" mode. Screen display during Auto Sync AUTO SYNC button Auto Sync Display Function Used to set the screen displayed during Auto Sync. Select "Auto Sync Disp" in the "Fine Sync" menu on the menu screen. For operating the menu screen, see pages 42 to 45. Note · · . . . . . The computer image being adjusted is displayed. -50 Easy to Use Functions Easy to Use Functions Selecting the Picture Display Mode This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose "NORMAL", "FULL", "DOT BY DOT", "BORDER", "STRETCH" or "SMART STRETCH" image. Switching the Picture Display Using Different Input Signals Press . · Each time is pressed, the display changes as shown on page 52 and 53. RESIZE button Info · In the Dot by Dot Mode, images are displayed in the original resolution, therefore they will not be enlarged. · To return to the standard image, press while "RESIZE" is displayed on the screen. Screen display of the picture display mode COMPUTER SVGA (800 × 600) XGA (1024 × 768) SXGA (1280 × 960) SXGA+ (1400 × 1050) SXGA (1280 × 1024) NORMAL 800 × 600 800 × 600 800 × 600 800 × 600 750 × 600 FULL -- -- -- -- 800 × 600 DOT BY DOT -- 1024 × 768 1280 × 960 1400 × 1050 1280 × 1024 4:3 aspect ratio Other aspect ratios · "NORMAL" is fixed when SVGA (800 × 600) signals are entered. Output screen image Input Signal NORMAL FULL DOT BY DOT Projects a full screen image Projects a full screen image Projects the original resolution while maintaining the aspect ratio. signal of the image. Resolution lower than SVGA 4:3 aspect ratio SVGA 4:3 aspect ratio Resolution higher than SVGA 4:3 aspect ratio SXGA (1280 × 1024) -52 VIDEO NORMAL 480I, 480P, 580I, 580P, 4:3 aspect ratio. NTSC, PAL, SECAM Letter box, squeeze 540P 16:9 aspect ratio 720P, 1035I, 1080I 16:9 aspect ratio 800 × 600 -- -- FULL -- 800 × 600 -- BORDER 600 × 450* -- -- 800 × 450* STRETCH SMART STRETCH 800 × 450* -- -- · "STRETCH" is fixed when 720P, 1035I or 1080I signals are entered. * The Digital Shift function can be used with these images. Output screen image BORDER Projects 4:3 image fully in STRETCH (the following column) image. NORMAL Input Signal Projects a full screen image. FULL Projects the center part in a 4:3 screen by enlarging 1. 3 times toward the horizontal direction. STRETCH Projects 16:9 image evenly over entire screen (top/bottom black bands). SMART STRETCH Projects the image fully in a 16:9 screen by enlarging only the surrounding areas while keeping the aspect ratio in the middle part of the image at 4:3. 4:3 aspect ratio 480I, 480P, 580I, 580P, NTSC, PAL, SECAM Letter box Squeeze 16:9 aspect ratio 540P 16:9 aspect ratio (4:3 aspect ratio in 16:9 screen) Easy to Use Functions 720P, 1035I, 1080I 16:9 aspect ratio -53 Displaying a Still Image This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience. Freezing a Moving Image 1 Press . · The projected image is frozen. FREEZE button "On-screen Display 2 Press again to return to the moving image from the currently connected device. 54 -54 Enlarging a Specific Portion of an Image This function allows you to enlarge a specific portion of an image. This is useful when you want to display a detailed portion of the image. Displaying an Enlarged Portion of an Image 1 Press . ', ", \, | · Enlarges the image. or enlarges or re· Pressing duces the projected image. buttons ENLARGE (Enlarge/ Reduce) buttons Note To enlarge ×1 ×2 ×3 ×4 ×9 ×16 ×36 ×64 To reduce · You can change the location of the enlarged image using ', ", \ and |. · When an image with a resolution higher than XGA is displayed, "×2" and "×3" cannot be selected. "On-screen Display Easy to Use Functions 2 Press to cancel the operation, then the magnification returns to ×1. Note In the following cases, the image will return to the normal size (×1). · When the input signal resolution and refresh rate (vertical frequency) change. -55 Gamma Correction Function Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. [. . . ] 34 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 PRJ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]