User manual SHARP PC-AX10

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If these equipments do cause harmful interference to radio or television reception, which can be determined by turning the equipments off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. [. . . ] It may cause malfunction of your computer and the drive. Ejecting Floppy Disk Before ejecting the floppy disk, make sure the indicator of the floppy disk drive unit is not lit. Eject it and store it properly. Eject Button 4-4 Formatting Floppy Disk 1. Make sure the floppy disk is not write-protected, and insert it into the floppy disk drive. · When you format a floppy disk that already contains data, all of the data stored on the disk will be lost. · You cannot format a double-density (2DD) 720KB floppy disk. Removing Optional External Floppy Disk Drive Unit To remove the unit, you need to perform the following steps before you remove it: 1. Click Safely remove Mitsumi USB Floppy ­ Drive(A:); then, Safe To Remove Hardware dialog appears. Remove the unit from your computer. 4 External Display You can use an external monitor with your computer. To display the images on both displays simultaneously, use the 1024x768 resolution. · Some monitors, which are not compatible with your computer, may not display correctly. · In this section, you often see the expression "Display Properties dialog box. " To open the dialog box, right-click somewhere on the Windows desktop and select Properties from the pop-up menu. 4-5 Connecting External Monitor 1. Open the display connector cover. 4 Cover Be sure to close the connector cover when the connector is not used. . 3. Connect one end of the display cable to the display connector, then, the other end of the display cable to your external monitor. If the button is not inside your computer cabinet, push it back into the cabinet. 4 PC Card Slot PC Card Eject Button 4-11 2. Insert a PC card into the slot with the label face up until it locks into place. Label Face Up 4 If the dialog box asking you What do you want Windows to do?appears, select the task you want. Ejecting PC Card · Some PC cards may become hot after long use. Click Safely remove xxxx (xxxxx is the name of your PC card); then, Safe To Remove Hardware dialog appears. 4-12 3. Push the PC card eject button so that it will pop out from the side of your computer. 4. Push the eject button until the inserted PC card pops out; then, remove it. 4 5. Push the PC card eject button all the way inside the cabinet for safekeeping. 4-13 Printer You can connect a USB printer to any of the USB ports on your computer. Before using a printer, read the printer manual and install the printer driver. Connecting Printer · Be sure to read the printer manual before connecting a USB printer to your computer. Some printer may not use Found New Hardware wizard to install the printer driver. · When connecting the cable to either of the USB ports on the right side of your computer, be sure to let the USB mark side up, and let the USB mark side down when using the USB ports on the rear side of your computer. You can connect the USB printer to your computer without turning off your computer. 4 Right Side Printer USB Ports USB Cable 4-14 CHAPTER 5 Communication Functions This chapter explains how to use the built-in modem, the wired LAN unit, and the wireless LAN function. · When you use communication software: · Connect your computer to the AC power source. (Refer to Disabling Power Management of Chapter 3. ) · See also the manual or online help of the software you are using. · The communication speed may vary depending on the traffic, local telecommunications infrastructure, and ISP (Internet Service Provider) infrastructure. Built-in Modem You can use the built-in modem for data transfer and fax communication. [. . . ] Type exit; then, press Enter. · Trouble with Peripherals Question: Why don't peripheral devices function? · · · · · · · · · Confirm they are correctly connected to your computer. Confirm drivers necessary for the devices are installed. Question: Why can't I print? Make sure the printer is turned on. Click start - Control Panel - Printers and Other Hardware ­ Printers and Faxes. T-9 Troubleshooting · · · · See also the Windows help program by clicking start - Help and Support. Question: Why don't peripheral devices function correctly? Set System standby/hibernate to Never in Power Options Properties dialog box. [. . . ]