User manual SHARP PC-A250

[. . . ] Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5. 0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs contact the telephone company to determine the maximum REN for the calling areas. If the terminal equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. [. . . ] See the attached specification sheet to confirm your computer has a built-in wireless LAN function. There are two kinds of wireless networks: a network using an access point and a peerto-peer wireless network. You can connect your computer to a wired LAN or the Internet through an access point that is also compliant with IEEE 802. 11b standard. Peer-to-peer wireless network consists of a number of computers each equipped with wireless networking interface. Each computer can communicate directly with other wireless enabled computers. The range to give reliable performance and the quality of connection vary depending on the environment where you perform. To communicate with the wireless LAN, activate the integrated antennas with the following steps. Activate Antennas You can enable/disable the antennas by pressing Fn +F1 key combination. When the antenna indicator ( ) lights green, the antennas are enabled. When the indicator light is off, they are disabled. Antenna Indicator 7 Connecting to the Internet via an Access Point You can connect your computer to the Internet or a wired network via an access point supporting IEEE 802. 11b. Refer to the manual of the access point or consult your network administrator if you are not sure. Communicating with Other Computers · Confirm each computer is enabled for wireless LAN first. · Make sure to log on the computer as a member of the Computer administrators group. Select Wireless Network Connection; then, click Change settings of this connection of Network Tasks. ) icon on the taskbar; then, click View Available Wireless · 1. 2. Select the desired network in the Available networks list; then, click Connect button. Question: Why can't I connect to the network via an access point? · · · Confirm Any available network (access point preferred) is selected in Networks to access of Advanced dialog box. (To open Advanced dialog box, refer to Communicating with Other Computers section on page 8. ) Confirm the ESSID of your computer matches the ESSID of the access point you want to communicate with. The Software is only authorized for distribution together with a specific computer. This License authorizes you to use the Software for disaster recovery purposes only, to restore the hard disk image contained on the CD to the computer with which the CD and Software were originally shipped. Without the express permission of PowerQuest, you may not (a) use, copy, modify, alter, or transfer, electronically or otherwise, the Software or documentation except as expressly permitted in this License Agreement, or (b) translate, reverse program, disassemble, decompile, or otherwise reverse engineer the Software. Any and all technical support questions, regarding the Software, should be referred to the place of purchase. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provision applies: It is acknowledged that the Software and the documentation were developed at private expense and that no part is in the public domain and that the Software and documentation are provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in 12 Technical Data and Computer Software clause at DFARS 252. 227-7013or subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52. 227-19, as applicable. If the Software fails to perform substantially in accordance with the documentation provided to your hardware supplier, PowerQuest will repair or replace the copy of the Software provided to your hardware supplier and will authorize your hardware supplier to provide such repaired or replaced Software to you without charge. NEITHER POWERQUEST NOR ITS SUPPLIERS SHALL IN ANY EVENT BE LIABLE FOR ANY DAMAGES WHATSOEVER ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, AND DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHER PECUNIARY LOSS, EVEN IF POWERQUEST CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, WHETHER SUCH LIABILITY IS BASED ON CONTRACT, TORT, WARRANTY, OR ANY OTHER LEGAL OR EQUITABLE GROUNDS. [. . . ] This process will format the whole hard disk drive and creates a new partition. The contents of the hard disk are restored to its original state in C: drive. · · 14 Formatting the drives and re-installing Windows XP 1. If any peripheral devices are connected to your computer, disconnect them. If the battery is completely discharged, the installation process will be canceled. 4. [. . . ]