User manual SHARP NOTEVISION XR-10S OPERATION MANUAL

[. . . ] Introduction MULTIMEDIA PROJECTOR MODEL Quick Start PG-MB66X/PG-MB56X XG-MB50X-L XR-11XC-L XR-10X-L/XR-10S-L OPERATION MANUAL Setup Connections Basic Operation Useful Features Appendix IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10. Model No. : Serial No. : Before using the projector, please read this operation manual carefully. Introduction Introduction 1. WARRANTY ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2. [. . . ] 0 END 2 Press P/Q or O/R to adjust the Keystone Correction. · You can also adjust the Keystone Correction using the adjustment buttons on the projector. Shrinks upper side. (Move the slide bar in the + direction. ) Basic Operation Note · Press l RETURN while the on-screen display of the Keystone Correction mode is on the screen to return to the default setting. Shrinks lower side. (Move the slide bar in the - direction. ) 3 Press g KEYSTONE. · The on-screen display of the Keystone Correction mode will disappear. · You can also use d KEYSTONE on the projector. Info · While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. When using PG-MB66X or PG-MB56X · The projector automatically detects tilt and the AUTO KEYSTONE feature automatically corrects trapezoidal distortion. Note · Automatic Keystone Correction may not work well in some cases, such as when the screen is leaning, temperature is extremely high or low, or zoom is at maximum or minimum. In these cases, fine adjust the Keystone Correction following steps 1 to 3. · You can select "On" or "Off" for the Auto Keystone Correction mode. (See page 41. ) 31 Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose "NORMAL", "BORDER" or "STRETCH" image. Press HRESIZE. · See page 41 for setting on menu screen. RESIZE button Computer NORMAL PG-MB66X/MB56X/ XG-MB50X-L/ XR-11XC-L/10X-L SVGA (800 K 600) XGA (1024 K 768) SXGA (1280 K 960) SXGA L (1400 K 1050) SXGA (1280 K 1024) 1280 K 720 XR-10S-L BORDER PG-MB66X/MB56X/ XG-MB50X-L/ XR-11XC-L/10X-L XR-10S-L STRETCH PG-MB66X/MB56X/ XG-MB50X-L/ XR-11XC-L/10X-L XR-10S-L 4:3 aspect ratio 1024 K 768 800 K 600 768 K 576 600 K 450 1024 K 576 800 K 450 Other aspect ratios 1024 K 768 J 800 K 600 J 768 K 576 J 600 K 450 J 1024 K 576 1024 K 576 800 K 450 800 K 450 Input Signal Computer Output screen image PG-MB66X/MB56X/ XG-MB50X-L/ XR-11XC-L/10X-L Resolution lower than XGA Image type NORMAL BORDER STRETCH XR-10S-L Resolution lower than SVGA XGA SVGA 4:3 aspect ratio Resolution higher than XGA Resolution higher than SVGA SXGA (1280K1024) 5:4 aspect ratio 1280K720 16:9 aspect ratio * Mode for projecting an image with the original aspect ratio without cutting any portions. : Cutout area on which images cannot be projected. 32 VIDEO · "STRETCH" is fixed when 540P, 720P or 1080I signals are entered. Input Signal DVD / Video Image type NORMAL Output screen image BORDER STRETCH 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Letter box Squeezed 16:9 image Squeezed 4:3 image Basic Operation 16:9 aspect ratio 540P, 720P, 1080I 16:9 aspect ratio (4:3 aspect ratio in 16:9) * Mode for projecting an image with the original aspect ratio without cutting any portions. : Area on which the image is not included in the original signals. 33 Operating with the Remote Control Adjustment buttons (P/R/O/Q) BREAK TIMER button FREEZE button Auto Sync (Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press FAUTO SYNC to manually adjust with Auto Sync function. Note PICTURE MODE button AUTO SYNC button · When the optimum image cannot be achieved with Auto Sync adjustment, use the help menu for manual adjustments. (See page 46. ) Displaying and Setting the Freezing a Moving Image Break Timer 1 1 Press k BREAK TIMER. · The timer starts to count down from 5 minutes. Press NFREEZE. · The projected image is frozen. 2 ROn-screen display Press NFREEZE again to return to the moving image from the currently connected device. 2 Press P /R /O /Q to adjust the length of the break time. · Increases with P or Q · Shortens with O or R 5 minutes s 6 minutes s 60 minutes 4 minutes s 3 minutes s1 minute · The break time can be set in units of one minute (up to 60 minutes). Selecting the Picture Mode You can select the appropriate picture mode for the projected image, such as movie or video game. Press GPICTURE MODE. · When pressing GPICTURE MODE, the picture mode changes in the following order: Standard Presentation Movie Game sRGB Canceling the break time display function Press k BREAK TIMER. Note · Break Timer does not function while the projector is operating the "Auto Sync", "FREEZE" or "AV MUTE" functions. * Note · See page 39 for details on the picture mode. * "sRGB" is displayed only when RGB signal is input. 34 Menu Items The following shows the items that can be set in the projector. Main menu Sub menu Picture Mode "Picture" menu INPUT 1 (RGB)/INPUT2 (RGB) Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 7500K 1 Bright PRJ - ADJ Standard Help Picture Page 39 Page 39 Standard Presentation Movie Game sRGB*1 +30 +30 +30 *1 +30 *1 +30 *2 +30 *2*6 +30 *2 Contrast Bright Red Blue Color Tint Sharp -30 -30 -30 -30 -30 -30 -30 ENTER END Page 40 CLR Temp INPUT 1 (Component)/INPUT 2 (Component)/INPUT 3/INPUT 4 Picture Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL. /ADJ. SCR - ADJ 0 0 0 0 0 7500K 1 3D Progressive Bright ENTER END PRJ - ADJ Standard Help Page 40 5500K 6500K 7500K 8500K 9300K 10500K Bright Boost [0/1/2] Page 40 Progressive *2 Page 40 Lamp Setting 2D Progressive 3D Progressive Film Mode Bright Eco + Quiet Page 40 Reset Main menu SCR - ADJ Resize Sub menu "Screen adjustment (SCR-ADJ)" menu Picture Resize Image Shift Keystone Auto Keystone OSD Display Background Setup Guide PRJ Mode Language SEL. /ADJ. SCR - ADJ 0 0 Off On Logo On Front English ENTER END PRJ - ADJ Normal Help Page 41 Page 41 Image Shift -96 -75 +96 +75 *3 *4 Normal Border Stretch Page 41 Keystone -127 -100 +127 *3 +100 *4 Page 41 Auto Keystone [On/Off] *5 Page 41 OSD Display [On/Off] · You can adjust the menu items with icons ( , , and ) using the respective buttons on the remote control. *2 Items when inputting component signal through INPUT 1 or INPUT 2, or when selecting INPUT 3 or INPUT 4. *3 Adjustment range for PG-MB66X/PG-MB56X/XG-MB50X-L/ XR-11XC-L/XR-10X-L. *6 "Tone" will appear on the menu screen only when PAL or SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust "Tone", but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals. Page 42 Background Useful Features Page 42 Setup Guide [On/Off] Logo Blue None Page 42 PRJ Mode Page 42 Language Front Ceiling + Front Rear Ceiling + Rear English Deutsch Español Nederlands Français Italiano Svenska Português Page 42 35 Menu Items (Continued) "Projector adjustment (PRJ-ADJ)" menu Main menu Picture Auto Search Auto Sync Auto Power Off System Sound Speaker RS-232C Fan Mode System Lock Lamp Timer(Life) SEL. /ADJ. SCR - ADJ PRJ - ADJ On On On On On 9600 bps Normal Help PRJ - ADJ Auto Search [On/Off] Sub menu Page 43 Page 43 Auto Sync [On/Off] Page 43 Auto Power Off [On/Off] Page 43 System Sound [On/Off] 0h ENTER 100% END Page 43 Speaker [On/Off] Page 43 RS-232C Page 44 Fan Mode 9600 bps 115200 bps Normal High Old Code New Code Reconfirm Page 44 System Lock Page 44 Lamp Timer(Life) Page 44 "Help" menu Picture SCR - ADJ PRJ - ADJ Help The items you can set with the "Help" menu "Help" menu n Page 46 · Vertical stripes or flickering image appear Auto Sync Adjust vertical noise Adjust horizontal noise · Data image is not centered Auto Sync H-Pos V-Pos · Color is faded or poor INPUT 1 or INPUT 2 Signal type: Auto/RGB/Component INPUT 3 or INPUT 4 Video System: A u t o / P A L / S E C A M / NTSC3. 58/NTSC4. 43/PALM/PAL-N/PAL-60 * The selectable items vary depending on the input signal and the selected input mode. There is no picture or audio Vertical stripes or flickering image appear Data image is not centered Color is faded or poor Picture is dark The image is distorted Reset all adjustments to default settings SEL. ENTER END 36 Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Adjustment buttons (P/R/O/Q) MENU/HELP button ENTER button RETURN button · Press l RETURN to return to the previous screen when the menu is displayed. Menu Selections (Adjustments) Example: Adjusting "Bright". · This operation can also be performed by using the buttons on the projector. 1 2 Press BMENU. · The "Picture" menu screen for the selected input mode is displayed. Example: "Picture" screen menu for INPUT 1 (RGB) mode Menu item Picture Picture Mode Contrast Bright Red Blue CLR Temp Bright Boost Lamp Setting Reset SEL. /ADJ. [. . . ] SIGNAL: Same as above S-video input signal 4-pin mini DIN connector (INPUT 3) Y (luminance signal): 1. 0 Vp-p, sync negative, 75 terminated C (chrominance signal): Burst 0. 286 Vp-p, 75 terminated Video input signal RCA connector: VIDEO, composite video, 1. 0 Vp-p, sync negative, 75 (INPUT 4) terminated Vertical frequency 45­85 Hz Horizontal frequency 15­70 kHz Pixel clock 12­108 MHz RS-232C terminal 9-pin mini DIN connector Audio input signal ø3. 5 mm minijack or RCA terminal: 0. 5 Vrms, more than 22 k (stereo) Audio output signal ø3. 5 mm minijack: 0. 5 Vrms, less than 2. 2 k (AUDIO OUTPUT 1-4) Speaker system 4 cm × 2. 85 cm oval × 1 Rated voltage AC 100­240 V Input current [PG-MB66X/PG-MB56X] 3. 6 A [XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L] 3. 0 A Rated frequency 50/60 Hz Power consumption PG-MB66X 350 W ("Bright" mode)/280 W ("Eco + Quiet" mode) with AC 100 V PG-MB56X 330 W ("Bright" mode)/270 W ("Eco + Quiet" mode) with AC 240 V XG-MB50X-L/XR-10X-L 298 W ("Bright" mode)/229 W ("Eco + Quiet" mode) with AC 100 V XR-11XC-L/XR-10S-L 288 W ("Bright" mode)/223 W ("Eco + Quiet" mode) with AC 240 V Power consumption 4. 7 W (AC 100 V) ­ 6. 1 W (AC 240 V) (standby) Heat dissipation PG-MB66X 1, 315 BTU/hour ("Bright" mode)1, 050 BTU/hour ("Eco + Quiet" mode) with AC 100 V PG-MB56X 1, 240 BTU/hour ("Bright" mode)/1, 010 BTU/hour ("Eco + Quiet" mode) with AC 240 V XG-MB50X-L/XR-10X-L 1, 120 BTU/hour ("Bright" mode)/860 BTU/hour ("Eco + Quiet" mode) with AC 100 V XR-11XC-L/XR-10S-L 1, 080 BTU/hour ("Bright" mode)/840 BTU/hour ("Eco + Quiet" mode) with AC 240 V Operating temperature 41°F to 95°F (+5°C to +35°C) Storage temperature ­4°F to 140°F (­20°C to +60°C) Cabinet Plastic I/R carrier frequency 38 kHz Dimensions (approx. ) 12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only) 12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjustment foot and projecting parts) Weight (approx. ) 8. 6 lbs. (3. 9 kg) Replacement parts Remote control, Power cord, RGB cable, 3 RCA to 15-pin D-sub cable, DIN-Dsub RS-232C adaptor, Operation manual, Dust filter As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. 64 Dimensions Units: inches (mm) 13 23 /64 (9) 11 1/32 (280) /64 (5) ø9 7/64 (69. 2) 7 /16 (11) 4 19/64 (109) 3 5/32 (80) 12 13/32 (315) 3 1/16 (77. 5) 2 7/8 (73) 1 55/64 (47) 1 7/8 (47. 5) 4 7/64 (104) Appendix 1 11/32 (33. 8) 2 61/64 (75) 1 53/64 (46. 2) 2 19/32 (65. 5) 7 /16 (11) 65 Index 3 RCA to 15-pin D-sub cable . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]