User manual SHARP MX-M363 BROCHURE

[. . . ] This manual explains settings related to general use of the machine, settings for the copy function, and settings for the document filing function. For administrator settings related to the printer function, fax function, network scanner function, and Internet fax function, see the following manuals: Printer . Operation manual (for facsimile), chapter 8 Network scanner / Internet fax . Operation manual (for image send), chapter 8 To access the administrator settings, the administrator password must be entered. General settings These settings are used to enable number-based auditing mode, adjust power consumption, manage the machine and peripheral devices, specify the network connection method, and configure security parameters. [. . . ] Disabling of large capacity cassette Use this setting when you wish to prohibit the use of the large capacity cassette or when it has failed. Disabling of stapler This setting is used to disable stapling when the stapler unit of the finisher or the saddle stitch finisher malfunctions. Disabling of punch Use this setting when you wish to prohibit punching or when the punch unit of the finisher or saddle stitch finisher has failed. Disabling of finisher Use this setting when you wish to prohibit the use of the finisher or saddle stitch finisher, or when either has failed. Disabling of inserter Use this setting when you wish to prohibit the use of the inserter or when it has failed. Disabling of covers/inserts mode Use this setting to prohibit the use of covers/inserts mode. 11 GENERAL SETTINGS Saddle stitch position adjust This setting is used to adjust the stapling position (folding position) when the saddle stitch function of the optional saddle stitch finisher is used. The value can be adjusted in 0. 25 mm increments within ±2. 00 mm from the reference position for each paper size. Max. +2mm Position adjusted to the plus direction Min. -2mm Position adjusted to the minus direction Rotated output When Rotated output is turned on, you can have the paper output orientation (A4-size paper only) of each set of copies alternate between horizontal and vertical. This function is used to sort output when neither the Finisher peripheral nor the Saddle stitch finisher peripheral are installed. * To use this function, A4-size paper must be loaded both horizontally and vertically in the paper trays. This function works when paper is output to the centre tray. 1 2 11 12 Reference position [AUTOMATIC SADDLE STITCH] checkmark The saddle stitch print function can normally be divided into the following three general steps. The pages of the original are automatically reordered to allow saddle stitch binding (saddle stitch function). IPv4 setting IPv6 setting Enable TCP/IP Enable NetWare Enable EtherTalk Enable NetBEUI Reset the NIC Tandem setting PING command NOTE For setting and modification of "Network settings", be sure to consult with the network administrator. IPv4 setting When using this product in a network that uses the TCP/IP protocol (IPv4), use this setting to set the IP address (IP address, IP subnet mask, and IP gateway) of this product. The setting is set to ENABLE DHCP by factory default setting, which obtains the IP address setting automatically. When using this product on a TCP/IP network, be sure to turn on the "Enable TCP/IP" setting below. If DHCP is used, the IP address assigned to the machine may be changed automatically on occasion. IPv6 setting When using this product in a network that uses the TCP/IP protocol (IPv6), use this setting to set the IP address (enable IPv6, DHCPv6, IP address, prefix length, and default gateway) of this product. When using this product on a TCP/IP network, be sure to turn on the "Enable TCP/IP" setting below. If DHCP is used, the IP address assigned to the machine may be changed automatically on occasion. If this happens, printing will not be possible. Enable TCP/IP When using this product in a network that uses the TCP/IP protocol, set this setting. Also set the IP address using the setting "IP address setting" above. Default setting: Enable Enable NetWare When using this product in a network that uses the NetWare protocol, set this setting. [. . . ] NOTE When 6 or 8 names per screen is selected, each displayed key name can be up to 18 characters long. When 12 names per screen is selected, each key name can only be up to 10 characters long. Sort method setting This setting is used to select how lists of files stored in the "MAIN FOLDER", "CUSTOM FOLDER", and "QUICK FILE FOLDER" are ordered. Document output options This setting is used to select the operations (print and send) that are allowed for stored files. [. . . ]