User manual SHARP MX-M350 DATASHEET

[. . . ] If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. The equipment should be installed near an accessible socket outlet for easy disconnection. Notice for users in the UK MAINS PLUG WIRING INSTRUCTIONS The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse and of the same rating as the one removed from the plug must to BS1362 marked or be used. Always refit the fuse cover after replacing the fuse on the moulded plug. [. . . ] · If you selected "SIZE INPUT", follow steps 4 through 6 of the procedure in "USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL" (page 51) to set the horizontal and vertical dimensions of the original. 50 COPY FUNCTIONS USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL When the bypass tray is being used for copying and an original that is placed on the document glass is detected as being a special size, the display will prompt the user to set the original size. To make a copy in this type of situation, follow the steps below. 1 2 Load paper in the bypass tray and place the original on the document glass. Touch the [PAPER SELECT] key and then select the bypass tray. 5 Press the [OK] key. If "SIZE INPUT" was selected in step 4: OK RE PAPER SELECT COPY RATIO AUTO IMAGE ODE RESOLUTION ADDRESS FORMAT O AM RESOLUTION ADDRESS BROADCAST O [OK]:ORIG. SIZE ENTER AUTO SIZE INPUT SIZE(mm) X: 210 Y: 148 100% EXTRA A message will appear asking you whether you wish to set the original size or make the copy without setting it. To make a copy without setting the original size, press the [START] key ( ). To set the original size, go to step 3. If you load thick paper in the bypass tray, press the [PAPER] key until "EXTRA" is highlighted. The setting is cleared when "Auto clear" works or the [CA] key is pressed. For restrictions on paper types and weights, see "PAPER" (page 18). The size entry screen appears and is ready for entry of the width of the original. Note If you selected inches in step 4, the screen will be ready for you to enter the width in inches. If other than "SIZE INPUT" was selected in step 4: You will return to the base screen. Go to step 8. Note 6 Select "X" (width) with the [ ] or [ ] key and enter the width with the [ ] or [ ] key, and then do the same for the length (Y). 4 [OK]:ORIG. SIZE ENTER AUTO SIZE INPUT SIZE(mm) X: 100 Y: 100 · Any number from 64 mm to 432 mm (2-1/2" to 17") can be entered for the width, and any number from 64 mm to 297 mm (2-1/2" to 11-5/8") can be entered for the length. · The entered size is retained until the power is turned off, even if "SIZE INPUT" is selected again and the entry screen of step 5 is displayed. 100% EXTRA Note 3 Press the [OK] key. OK GHI BACK PQRS PY AN ORIG. (Enlargement cannot be set. ) · If automatic ratio selection has been selected, the XY zoom feature cannot be selected. If the XY zoom feature is selected, automatic ratio selection cannot be selected. · Ratios that can be selected are 25% to 400% (50% to 200% when the SPF is used). 1 Place the original in the document feeder tray or on the document glass. 4 Select "XY ZOOM" with the [ ] or [ ] key. PQ ED COPY LEX SCAN LEX SCAN ACC SPECIAL MODES DUAL PAGE COPY 2in1/4in1 XY ZOOM [OK]:ADJUST 2 Press the [SPECIAL FUNCTION] key. 5 Press the [OK] key. OK ON LINE DATA SPECIAL FUNCTION LINE DATA COPY EXPOSURE PAPER SE SCAN COLOUR MODE RESOLUT The special function screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST XY ZOOM 115% ZOOM 100% X: 100% 86% Y: 100% [ ]:X Y 3 Press the [OK] key. OK GHI The XY zoom screen will appear, ready for selection of the X (horizontal) ratio. BACK PQRS PY AN The special modes screen will appear. SPECIAL MODES MARGIN SHIFT ERASE DUAL PAGE COPY [OK]:ADJUST 6 Set the horizontal ratio with the [ ], [ ], [ ], or [ ] keys. A preset ratio can be selected with the [ ] or [ ] keys. The ratio can be adjusted in increments of 1% with the [ ] or [ ] keys. 54 COPY FUNCTIONS 7 Press the key. 11 XY ZOOM 115% ZOOM 100% X: 115% 86% Y: 100% [ ]:X Y MNO WXYZ Select any other copy settings as needed and press the [START] key ( ). @ ACC. #-C READ @. -_ AD-END The vertical ratio can now be selected. 8 Set the vertical ratio with the [ ], [ ], [ ], or [ ] keys. A preset ratio can be selected with the [ ] or [ ] keys. The ratio can be adjusted in increments of 1% with the [ ] or [ ] keys. To change the copy ratio in the horizontal direction again, press the key. Note If the [COPY RATIO] key is pressed when XY zoom ratios are set, the following screen appears. XY ZOOM ADJUST OFF 9 Press the [OK] key. OK To cancel the XY zoom ratio settings, select "OFF" and press the [OK] key. To adjust the XY zoom copy ratios, select "ADJUST" and press the [OK] key. Ready to copy. A4R AUTO 4 You will return to the base screen. X115% Y 99% AUTO B4 10 Make sure that the desired paper tray is selected. If the auto paper select function has been enabled, the appropriate copy paper size will be automatically selected based on the original size and the selected copy ratios. Image rotation will take place if necessary. 55 TWO-SIDED COPYING TWO-SIDED COPYING The machine is capable of the following types of automatic two-sided copying. [. . . ] 12 Tray 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Tray 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Troubleshooting - Machine/copying problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Two-sided copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]