User manual SHARP MX-3610N DATASHEET

[. . . ] These may degrade or discolour the housing. CLEANING THE DOCUMENT GLASS AND AUTOMATIC DOCUMENT FEEDER DOCUMENT GLASS DOCUMENT BACKPLATE SHEET If the document glass or document backplate sheet becomes dirty, the dirt will appear in the scanned image. To clean the document glass and document backplate sheet, wipe with a clean, soft cloth. If necessary, moisten the cloth with water or a small amount of neutral detergent. After wiping with the moistened cloth, wipe the parts dry with a clean dry cloth. SCANNING AREA Examples of how dirt can affect the image If black or white lines appear in images scanned using the automatic document feeder, clean the scanning area. [. . . ] While the paper tray descends, the operation button indicator will blink. After the paper tray finishes descending, the indicator will light solidly. Do not remove the paper until the indicator light solidly. 2 Remove the cover. While pushing the cover to the left, pull it forward. 2 Remove the cover. While pushing the cover up, pull it forward. 3 Clean the roller. After cleaning the roller, replace the cover to its original position. 3 Clean the roller. After cleaning the roller, replace the cover to its original position. 4 Set the paper. 4 Set the paper and press the operation button. After the button is pressed, the paper table will rise. While the paper tray rises, the operation button indicator will blink. After the paper tray finishes rising, the indicator will light solidly. 4 DISCARDING PUNCH WASTE Punch waste from punched holes is collected in the punch waste box. Follow the steps below to discard the punch waste. Finisher Finisher (for MX-M850) / saddle stitch finisher 1 Open the cover. 1 Open the cover. 2 Pull out the punch waste box and discard the punch waste. 2 Gently pull out the punch waste box and discard the punch waste. Discard the punch waste in a plastic bag or other container, taking care not to let the waste scatter. Discard the punch waste in a plastic bag or other container, taking care not to let the waste scatter. 3 Replace the punch waste box. 3 Make sure the punch waste box is replace correctly. Replace the punch waste box. Make sure the punch waste box is replace correctly. 4 Close the cover. 4 Close the cover. 5 DISCARDING STAPLE WASTE (FINISHER) When the finisher is used for stapling, staple waste is produced. Follow the steps below to discard the staple waste. 1 Open the cover. 3 Replace the staple waste box. Make sure the staple waste box is replace correctly. 2 Pull out the staple waste box and discard the staple waste. 4 Close the cover. Do not insert your fingers into the staple waste box. The staples may create holes in the bag. 6 REPLACING THE TONER COLLECTION CONTAINER The toner collection container collects excess toner that is produced during printing. To replace the toner collection container, follow the steps below. 1 Open the cover. 4 Install a new toner collection container. Slowly push the new container in until it stops. 2 Remove the toner collection container. The toner collection container may be heavy. Use both hands to firmly support the container while removing it. 5 Close the cover. Caution · Do not throw the toner collection container into a fire. Toner may fly and cause burns. 3 Place the cover on the removed toner collection container. Remove the cover from the toner collection container and attach the cover as shown. · Store the toner collection container out of reach of small children. This cannot be selected when the first screen appears. (D) Back Next Animation showing what to do. Touch to return to the first screen. (E) (C) (D) (E) 16 REMOVING MISFEEDS Detailed procedures for removing misfeeds are explained in this section. Use these procedures together with the information screen. MISFEED LOCATIONS Misfeeds can be detected in the locations below. In this manual, procedures for removing misfeeds are explained by device. FINISHER (FOR MX-M850) / SADDLE STITCH FINISHER page 24 BYPASS TRAY (MX-MFX1) / LARGE CAPACITY TRAY page 43 FINISHER page 18 SADDLE UNIT page 21 FOLDING UNIT page 28 THE MACHINE page 33 INSERTER page 30 BYPASS TRAY (MX-MFX2) / LARGE CAPACITY TRAYS page 39 · Do not damage or touch the transfer belt while removing misfed paper. · A misfeed may occur deep inside a compartment, so check the entire compartment carefully. · If the paper tears, be sure to remove all pieces from the machine. · After you have finished removing a misfeed, be sure to replace any covers or devices that were moved during misfeed removal back in their original positions. 17 REMOVING MISFEEDS FINISHER When a mark below blinks, a misfeed has occurred at that location. Output trays Inside Output trays Inside 1 Remove the misfed paper. 1 Open the cover. 2 Remove the misfed paper. 2 Pull the R1 lever up in the direction of the arrow. 3 Remove the misfed paper. After removing the paper, return the R1 lever to its original position. 18 REMOVING MISFEEDS 4 Push the R2 lever down in the direction of the arrow. 9 Remove the misfed paper. 5 Remove the misfed paper. After removing the paper, return the R2 lever to its original position. 10 Move the R5 lever in the direction of the arrow. 6 Pull the R3 lever up in the direction of the arrow. 11 Remove the misfed paper. 7 Remove the misfed paper. After removing the paper, return the R3 lever to its original position. 12 Move the R6 lever in the direction of the arrow. 8 Move the R4 lever in the direction of the arrow. 13 Remove the misfed paper. After removing the paper, return the R4 - R6 levers to their original positions. 19 REMOVING MISFEEDS 14 Move the R7 lever in the direction of the arrow. 15 Remove the misfed paper. After removing the paper, return the R7 lever to its original position. 16 Grasp the R8 lever and pull out the unit. Pull the unit out until it stops. 17 Remove the misfed paper. 18 Replace the unit and close the cover. 20 REMOVING MISFEEDS SADDLE UNIT When a mark below blinks, a misfeed has occurred at that location. Transport area Stapler section (page 22) Transport area 1 Open the cover. 4 Pull the M2 lever up in the direction of the arrow. 2 Pull the M1 lever up in the direction of the arrow. 5 Remove the misfed paper. When released, the M2 lever automatically returns to its original position. 3 Remove the misfed paper. When released, the M1 lever automatically returns to its original position. 6 Move the M6 lever in the direction of the arrow. 21 REMOVING MISFEEDS 7 Remove the misfed paper. When released, the M6 lever automatically returns to its original position. Stapler section 1 2 Open the cover. See step 1 of "Transport area" (page 21). Move the M4 lever in the direction of the arrow. 8 Open the cover. 3 9 Pull the M3 lever up in the direction of the arrow. Remove the misfed paper. After removing the paper, return the M4 lever to its original position. 4 10 Remove the misfed paper. When released, the M3 lever automatically returns to its original position. Move the M5 lever in the direction of the arrow. 5 11 Close all covers. Remove the misfed paper. After removing the paper, return the M5 lever to its original position. 22 REMOVING MISFEEDS 6 Turn the M8 knob in the direction of the arrow. 10 Remove the misfed paper. After removing the paper, return the M10 lever to its original position. Before performing step 7, be sure to turn the M8 knob. If you perform step 7 without turning the knobs, the paper may tear and torn pieces may remain in the machine. 11 Open the M11 lever in the direction of the arrow. 7 Grasp the M9 lever and pull out the unit. Pull the unit out until it stops. 12 Remove the misfed paper. After removing the paper, return the M11 lever to its original position. 8 Remove the misfed paper. 13 Replace the unit and close the cover. 9 Open the M10 lever in the direction of the arrow. 23 REMOVING MISFEEDS FINISHER (FOR MX-M850) / SADDLE STITCH FINISHER When a mark blinks in the image below, a misfeed has occurred at that location. Output trays Inside Output trays Inside 1 Remove the misfed paper. 1 Open the cover. 2 Remove the misfed paper. 2 Push the R3 lever down in the direction of the arrow. 3 Remove the misfed paper. 24 REMOVING MISFEEDS 4 Rotate the R2 knob in the direction of the arrow. 9 Remove the misfed paper. After removing the paper, return the R1 lever to its original position. 5 Pull the R4 lever up in the direction of the arrow. 10 Move the R5 lever in the direction of the arrow. 6 Remove the misfed paper. After removing the paper, return the R3/R4 levers to their original positions. 11 Remove the misfed paper. After removing the paper, return the R5 lever to its original position. 7 Push the R1 lever down in the direction of the arrow. 12 Move the R6 lever in the direction of the arrow. 8 Rotate the R2 knob in the direction of the arrow. 13 Remove the misfed paper. After removing the paper, return the R6 lever to its original position. 25 REMOVING MISFEEDS 14 Push the R3 lever down in the direction of the arrow. 18 Grasp the R10 lever (R8 lever on the finisher) and pull out the unit. Gently pull out the unit until it stops. 15 Move the R7 lever in the direction of the arrow. 19 Remove the misfed paper. 16 Remove the misfed paper. When released, the R7 lever automatically returns to its original position. After removing the paper, return the R3 lever to its original position. If you are using the finisher (for the MX-M850), go to step 24. 20 Open the R11 lever in the direction of the arrow. If you are using the finisher (for the MX-M850), go to step 18. 17 Rotate the R9 knob in the direction of the arrow. 21 Remove the misfed paper. After removing the paper, return the R11 lever to its original position. Be sure to turn the R9 knob before performing step 18. If you perform step 18 without turning the knobs, the paper may tear and pieces may remain in the machine. 26 REMOVING MISFEEDS 22 Open the R12 lever in the direction of the arrow. 23 Remove the misfed paper. After removing the paper, return the R12 lever to its original position. 24 Return the unit to its original position and close the cover. 27 REMOVING MISFEEDS FOLDING UNIT When the mark blinks in the image below, a misfeed has occurred at that location. Transport area Transport area 1 Open the cover. 4 Pull out the unit. Gently pull out the unit until it stops. 2 Pull the N1 lever up in the direction of the arrow. When the N1 lever is down, the unit cannot be pulled out. 5 Grasp the N2 lever and open the cover in the direction of the arrow. The cover opens in two stages. Gently open the cover until it stops. 3 Remove the misfed paper. 28 REMOVING MISFEEDS 6 Remove the misfed paper. After removing the paper, close the cover. 7 Grasp the N3 lever and open the cover in the direction of the arrow. 8 Remove the misfed paper. After removing the paper, close the cover. 9 Return the unit to its original position, push down the N1 lever, and close the cover. 29 REMOVING MISFEEDS INSERTER When a mark below blinks, a misfeed has occurred at that location. [. . . ] If you perform step 3 without turning the knob, the paper may tear and pieces may remain in the machine. 34 REMOVING MISFEEDS 3 Pull the lever up in the direction of the arrow so that it is horizontal. 6 Remove the misfed paper. 4 Pull out the unit. Keeping the lever horizontal, gently pull out the unit until it stops. When removing misfed paper, do not touch or damage the transfer belt. 7 Push the paper guide down in the direction of the arrow. After pulling the unit all the way out, make sure that the lever is points down slightly. This locks the unit. 8 If the conveyor unit is not locked when you remove a misfeed, your hand or fingers may become pinched by the devices. Remove the misfed paper. When released, the paper guide automatically returns to its original position. 5 Turn the knob in the direction of the arrow. 9 Pull the paper guide up in the direction of the arrow. 35 REMOVING MISFEEDS 10 Remove the misfed paper. When released, the paper guide automatically returns to its original position. 14 Pull the paper guide up in the direction of the arrow. 11 While pressing on the lever, open the unit. 15 Remove the misfed paper. When released, the paper guide automatically returns to its original position. Gently pull out the unit until it stops. 16 Open the paper guide. 12 Turn the knob in the direction of the arrow. 17 Remove the misfed paper. After removing the paper, close the paper guide. 13 Remove the misfed paper. 18 Pull the paper guide up in the direction of the arrow. 36 REMOVING MISFEEDS 19 Remove the misfed paper. When released, the paper guide automatically returns to its original position. Transport area 1 Open the cover. 20 Pull the paper guide up in the direction of the arrow. 2 Open the paper guide. While pressing on the green release button, open the paper guide in the direction of the arrow. 21 Remove the misfed paper. When released, the paper guide automatically returns to its original position. 3 Remove the misfed paper. Misfeed in tray 1 or tray 2 22 Return the unit to its original position and close the cover. Misfeed in tray 3 Misfeed in tray 4 4 Close the paper guide and close the cover. 37 REMOVING MISFEEDS Trays 1 to 4 Before pulling the tray out, be sure to verify that a misfeed has not occurred in the paper conveyor. If you pull the tray out without checking, you may tear misfed paper and make it more difficult to remove the pieces that remain in the machine. Transport area (page 37) 1 Pull out trays 1 and 2. Gently pull out the tray until it stops. 5 Pull out tray 3. Gently pull out the tray until it stops. 2 Remove the misfed paper. A misfeed has occurred inside the machine. [. . . ]