User manual SHARP LC-37HV4U

[. . . ] OPERATION MANUAL MODE D'EMPLOI MANUAL DE OPERACIN MANUAL DE OPERAO PORTUGUS LIQUID CRYSTAL TELEVISION TLVISEUR ACL TELEVISOR CON PANTALLA DE CRISTAL LIQUIDO TELEVISOR DE CRISTAL LQUIDO ESPAOL FRANAIS LC-37HV4U ENGLISH LC-37HV4U LIQUID CRYSTAL TELEVISION ENGLISH ENGLISH OPERATION MANUAL IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. [. . . ] 6 7 8 9 0 Signal name GND (Ground) GND (Ground) GND (Ground) 5V GND (Ground) Pin No. q w e r t Signal name Not connected SDA HD VD SCL NOTE Macintosh adaptor may be required for use for some Macintosh computers. Displaying an image from a PC TV TV POWER AV MODE CBL VCR DVD /SAT /LD /DTV ANT-A/B FRONT SURROUND TWIN PICTURE VIEW MODE FREEZE SELECT SUB INPUT TWIN CH MTS CC INPUT To view an image from a PC, select "PC" from the "INPUT SOURCE" menu using INPUT on the remote control unit or on the Display. (See page 50. ) When connecting to a PC, the correct input signal type is automatically detected. If the PC image does not come in clearly, you may need to set the Auto Sync. adjustment on the "Auto Sync. " in the "Setup" menu. (See page 49. ) You only need to select the input source on the "INPUT SOURCE" menu. NOTE Each time INPUT is pressed, the input source toggles. DISPLAY SLEEP EDIT/ LEARN INPUT SOURCE TV INPUT1 INPUT2 INPUT3 INPUT4 PC 46 Useful adjustment settings Image position (AV input mode only) For adjusting a picture's horizontal and vertical position. TV TV POWER AV MODE CBL VCR DVD /SAT /LD /DTV INPUT 1 Press MENU and the TV MENU screen displays. Press c/d to select "Setup". 2 3 ANT-A/B FRONT SURROUND TWIN PICTURE Press a/b to select "Position", and then press SET/ENTER. TV MENU Setup Option MTS CC SELECT SUB TWIN CH VIEW MODE FREEZE INPUT EZ Setup LEARN DISPLAY SLEEP EDIT/ CH Setup Parental CTRL Position 1 4 7 2 5 8 0 FLASHBACK 3 6 9 100 ENT Picture Flip Language [Standard] [English] 4 Press a/b to select "H-Pos. " or "V-Pos. ". Setup Position VOL MUTE CH H-Pos. MENU RETURN SOURCE POWER [0] [0] 10 30 +10 +30 TV/SAT/DVD MENU DTV/DVD TOP MENU DTV/SAT GUIDE V-Pos. Reset SET/ ENTER DTV/SAT INFO FAVORITE CH A POWER B INPUT C VOL VCR REC 5 D VOL Press c/d to adjust the item to your desired position. RECEIVER NOTE For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press SET/ ENTER. You can easily move the image position as shown on page 48, but when the power is switched off the image will return to the previously memorized position. Selected item H-Pos. V-Pos. Description Centers the image by moving it to the left or right. Centers the image by moving it up or down. 47 Useful adjustment settings Moving the picture on the screen You can move the picture around on the screen. FLASHBACK VOL MUTE CH Press a/b/c/d to move an image on the screen to the desired position. Press SET/ENTER to return to the initial image position. NOTE MENU RETURN SOURCE POWER TV/SAT/DVD MENU DTV/DVD TOP MENU DTV/SAT GUIDE SET/ ENTER DTV/SAT INFO FAVORITE CH A POWER B INPUT C VOL VCR REC D VOL RECEIVER While pressing a/b/c/d, an on-screen image, "Adjusting Position" displays to the desired position. Once the System shuts down or enters standby mode, the setting is erased. To move the picture around the screen again, you must perform the above procedure again. "TV", "INPUT1", "INPUT2", "INPUT3" and "INPUT4" can each adjust the image position setting on this page. Even when the image fills the screen, its position can be adjusted with this function. Initialize the image position by pressing SET/ENTER. 48 Useful adjustment settings Auto Sync. adjustment (PC input mode only) For automatically adjusting the PC image. MENU Fine Sync. adjustment (PC input mode only) Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimize the image. MENU TV/SAT/DVD MENU DTV/DVD TOP MENU DTV/SAT GUIDE RETURN SOURCE POWER TV/SAT/DVD MENU DTV/DVD TOP MENU DTV/SAT GUIDE SET/ ENTER RETURN DTV/SAT INFO SOURCE POWER FAVORITE CH A POWER B INPUT C VOL VCR REC SET/ ENTER D VOL FAVORITE CH A POWER B INPUT C VOL DTV/SAT INFO VCR REC RECEIVER D VOL 1 2 Press MENU and the PC MENU screen displays. Press c/d to select "Setup". Setup menu displays. RECEIVER 1 2 3 4 Press MENU and the PC MENU screen displays. Press c/d to select "Setup". Setup menu displays. 3 4 Press a/b to select "Auto Sync. ", and then press SET/ENTER. [. . . ] Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Model Specific Section Your Product Model Number & Description: LC-37HV4U LCD Color Television (Be sure to have this information available when you need service for your Product. ) Warranty Period for this Product: Additional Item(s) Excluded from Warranty Coverage (if any): Where to Obtain Service: One (1) year parts and labor from the date of purchase. To find the location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. [. . . ]