User manual SHARP LC-37DB5U

[. . . ] LC-37DB5U LIQUID CRYSTAL TELEVISION ENGLISH OPERATION MANUAL · The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual operations. · Menu items that are not selectable are grayed out. IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV. Model No. : Serial No. : IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Set whether or not to use VIEW MODE based on signal recognition, including an HDMI signal. Select "Analog" for audio signal via the RAUDIO -L terminal. 6 INPUT SOURCE TV INPUT1 INPUT2 INPUT3 INPUT4 HDMI Setup items Signal Type Color Matrix 2 Press MENU and the MENU screen displays. Dynamic Range Standard/ Out of standard 3 Auto View Enable/Disable Press c/d to select "Option". Press a/b to select "HDMI Setup", and then press ENTER. MENU [Option . . . HDMI Setup] Option Audio Only Digital Noise Reduction HDMI Setup Output Select Quick Shoot [Fixed] [Off] [Low] 4 Audio Select Digital/Analog NOTE · Refer to your external equipment operation manual for the signal type. 29 Useful adjustment settings Image position For adjusting a picture's horizontal and vertical position. Moving the picture on the screen You can move the picture around on the screen. Press ENTER to return to the original image position. NOTE 1 2 3 4 Press MENU and the MENU screen displays. Press c/d to select "Setup". Press a/b to select "Position", and then press ENTER. Press a/b to select "H-Pos. " or "V-Pos. ". H-Pos. V-Pos. [ 0] [ 0] ­10 ­20 +10 +20 Reset · While pressing a/b/c/d, an on-screen image, "Adjusting Position" displays to the desired position. To move the picture around the screen again, you must perform the above procedure again. · The image position setting using the steps on this page can be stored. · "TV", "INPUT1", "INPUT2", "INPUT3" and "INPUT4" can each adjust the image position setting on this page. · Even when the image fills the screen, its position can be adjusted with this function. · Press ENTER to reset the image to original positions. Selected item H-Pos. V-Pos. Description Centers the image by moving it to the left or right. Centers the image by moving it up or down. 5 Press c/d to adjust the item to your desired position. NOTE · For resetting all adjustment items to the factory preset values, press a/b to select "Reset", and then press ENTER. · You can easily move the image position as shown on this page, but when the power is switched off the image will return to the previously memorized position. 30 Useful adjustment settings Input Select INPUT button Selecting input source Use this menu to select the input source. 1 Press INPUT. · A list of selectable sources appears. 2 Press INPUT again to select the input source. · An image from the selected source automatically displays. · If the corresponding input is not plugged in, you cannot change the input. Be sure to connect the equipment beforehand. Selecting input signal type For setting the signal type of external equipment connected to INPUT 1 or 2 terminals. 1 2 3 4 Press MENU and the MENU screen displays. Press c/d to select "Option". Press a/b to select "Input Select", and then press ENTER. Press a/b to select a signal type you want to set, and then press ENTER. · If the selected signal type is incorrect, images are not displayed or displayed without any color. NOTE · If you set INPUT1 and INPUT2 to Auto, the TV will automatically select the input signal. · Check the operation manual of the external equipment for the signal type. · Setting INPUT 1 and INPUT 2 signal selection to "Auto" when other equipment is connected will result in the following connectivity priority. VIDEO 31 Useful adjustment settings Input Label Lets you set the input terminal displayed using the INPUT SOURCE menu or channel display. Picture flip You can set the orientation of the picture. 1 Press MENU and the MENU screen displays. 2 3 4 Press c/d to select "Setup". Press a/b to select the desired mode, and then press ENTER. 1 2 Press INPUT to select the desired input source. [. . . ] In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Model Specific Section Your Product Model Number & Description: LC-37DB5U LCD Color Television (Be sure to have this information available when you need service for your Product. ) One (1) year parts and labor from the date of purchase. [. . . ]