User manual SHARP KC-860U

[. . . ] KC-860U AIR PURIFIER with Humidifying Function OPERATION MANUAL Purificateur d’air à fonction d’humidification MANUEL D’UTILISATION Con función de humidificación MANUAL DE OPERACIÓN Device of this mark is a trademark of Sharp Corporation. “Plasmacluster” and “Device of a cluster of grapes” are registered trademarks of Sharp Corpration in Japan , USA and elsewhere. This product earned the ENERGY STAR by meeting strict energy efficiency guidelines set by the US EPA. US EPA does not endorse any manufacturer claims of healthier indoor air from the use of this product. [. . . ] Use of other water sources may promote the growth of mold, fungus and/or bacteria. The Water Tank by unlatching the OPERATION Fan Speed Quick Clean MODE Button Plasmacluster Button ON/OFF Button Clean Air MODE Button Clean Air & Humidify MODE Button Power OFF Button CLEAN AIR & HUMIDIFY MODE Use the Clean Air & Humidify Mode to quickly clean the air, reduce odors and to humidify. € If the power cord was not unplugged between uses, the unit will automatically re-start at the previously selected settings. (See E-13) About Automatic Humidify Mode The Temperature/Humidity sensors automatically detect and adjust humidity according to changes in room temperature. Depending on the size and humidity of the room, humidity may not reach 45 - 55 %. in such cases , it is recommended that CLEAN AIR & HUMIDIFY/MAX MODE be used. Temperature 64 and below 64-75 75 and above Humidity 55% 50% 45% CLEAN AIR MODE Use the Clean Air Mode when additional humidity is not required. € If the power cord was not unplugged between uses, the unit will automatically re-start at the previously selected settings. By continuously discharging strong airflow cycles, the unit effectively removes airborne dust, pollen, mold and allergens from the air as they are drawn through the filter system. The unit humidifies when there’s water in the Water Tank, and it operates without humidifying when there is no water in it. ENGLISH 2009/12/28 14:07:17 Press the MODE 1 the displayQUICK CLEANmode. Button on to select this When the operation finishes, the unit will return to the prior operation. FAN SPEED Button Press the FAN SPEED Button to select the preferred fan settings. Please note the fan speed cannot be adjusted during the QUICK CLEAN Mode. AUTO operation The fan speed is automatically switched (HIGH*, MEDIUM, LOW) depending on the amount of impurities in the air. POLLEN mode operation MAX operation MEDIUM operation LOW operation The unit will operate at High level for 10 minutes, then will alternated between MED and HIGH every 20 minutes. Plasmacluster ON/OFF Button Press the Plasmacluster ON/OFF Button to turn Plasmacluster Ion Mode ON and OFF. When Plasmacluster is ON, both the Indicator Light and Plasmacluster Indicator Light on the front display turn on. Indd 13 OPERATION LIGHTS CONTROL Button Use when the light on the front panel is too bright. Refer to the diagram to select the desired brightness on the front panel. €｢ ｣  ｢ ｣  ｢ ｣ The lights on the front panel are brighter. CAUTION The lights on the front monitor are always brighter when starting. [. . . ] true HEPA filter materials: • Filter: Polypropylene • Frame: Polyester Washable Deodorizing filter Materials: • Polyester , Rayon , Activated charcoal Humidifying filter materials: • Rayon , Polyester E-19 KC-860U_Eng. Indd 19 2009/12/28 14:07:20 ENGLISH True HEPA filter TROUBLESHOOTING Before calling for service, please review the Troubleshooting chart below, since the problem may not be a unit malfunction. REMEDY(not a malfunction) • Clean or replace the filters if they appear to be heavily soiled. (See E-15, E-16, E-18) • The air could be impure at the time the unit was plugged in. [. . . ]