User manual SHARP KB-3300JS

[. . . ] · Be sure your range is installed and grounded properly by a qualified installer or service technician. · To eliminate the need to reach over the cooktop, cabinet storage space above the cooktop should be avoided or a range hood installed. 2 INSTALLATION MANUAL IMPORTANT SAFETY INSTRUCTIONS If the information in this manual is not followed exactly, a fire or electrical shock may result causing property damage, personal injury or death. · ALL RANGES CAN TIP · INJURY TO PERSONS COULD RESULT · INSTALL ANTI-TIP BRACKET PACKED WITH RANGE · SEE ANTI-TIP BRACKET TEMPLATE FOR INSTALLATION INSTRUCTIONS · Never use the range for warming or heating the room. Prolonged use of the range without adequate ventilation can be dangerous. · Do not store or use gasoline or other flammable vapors and liquids near this or any other range. [. . . ] For mobile homes, new installations, recreational vehicles or areas where local codes do not permit grounding through neutral, a 4 conductor power supply cord kit rated at 240 volts or 208 volts minimum, 50 amperes and marked for use with ranges should be used. Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends. Risk of fire or electrical shock exists if an incorrect size range cord kit is used or the Installation Manual or strain relief clamp are disregarded. CAUTION Do not loosen the nuts which secure the factoryinstalled range wiring to the terminal block while connecting range. Electrical failure or loss of electrical connection may occur. ELECTRICAL SHOCK HAZARD · Electrical ground is required on this range. · Do not connect to the electrical supply until range is permanently grounded. · DISCONNECT POWER TO THE CIRCUIT BREAKER OR FUSE BOX BEFORE MAKING THE ELECTRICAL CONNECTION. · This range must be connected to a grounded, metallic, permanent wiring system or the grounding connector of the power cord should be connected to the grounding terminal or wire lead on the range. · Failure to heed these warnings could result in a fire, personal injury or electrical shock. INSTALLATION MANUAL 208/240 VOLT CONNECTION INSTRUCTIONS screw The range can be set for 208V or 240V. The voltage setting for your range is pre-set at 240V from the factory. 180° 240V ACCESS TO TERMINAL BLOCK Loosen screw on rear access cover and pull down as illustrated in strain relief clamp Figure 6 to access terminal block wiring connection. To close, return to original location and secure screw. strain relief clamp 1 Locate the voltage switch on the lower back side of the range. 4 Connect the green ground wire lead to the frame of the range using the ground screw and plate as shown in Figure 11. Be sure to install using the same hole in the frame where the ground screw was originally installed. 5 Make sure all connections are tightened securely and replace the rear access cover. See Figure 7. 3­wire permanent connection ­ follow steps 1, 2 and 5 below. Before wiring the range, review the suggested power source location drawings in Figure 2. If connecting to a 4-wire electrical system: 1 Follow the manufacturers Installation Instructions supplied with the strain relief clamp and install. 2 Strip insulation away from the ends of the permanent wiring for line 1, line 2 and neutral; also strip ground wire on 4-wire 4-WIRE CONNECTION Note: Non-terminated field wire compression connections must be set at approximately 90 in. /lbs. FOR 3 & 4-WIRE PERMANENT CONNECTIONS terminal block Connect line 2 here. red ite wh Note: Install strain relief clamp. Center or white wire must always be attached to the center terminal on block. Connect neutral (white or center) here. A user supplied strain relief clamp must be installed at this location. It requires 1 3/8-inches (3. 5 cm) diameter cord kit hole. terminal block line 1 neutral ground screw ground strap ground plate line 2 Connect line 1 here. bla Cut ground strap. Failure to install the Anti-Tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. [. . . ] For wall mount, locate the bracket by placing the back edge of the template against the rear wall and the side edge of template on the mark made referencing the side of the range. Place bracket on top of template and mark location of the screw holes in wall. If rear of range is further than 1 1/4-inches from the wall when installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. [. . . ]