User manual SHARP HT-SL75

[. . . ] By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling. In other Countries outside the EU If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don't purchase a new product. In the European Union If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. [. . . ] Front side of the sound bar SO UN D BA Left R HO ME TH EA TE R SY ST EM HT -SL7 0 For 46" (117 cm) TV sound bar assembly For model Use Sound bar cover joint (short : 55 mm HT-SL70 (2 - 5/32")) for 46" (117 cm) TV. Sound bar joint (short) Cover Note: Sound bar stand can be removed by pulling it off backward from the sound bar. Using stand (vertical arrangement) Use sound bar stand cover (257 mm For model (10 - 21/16" )). Cover Sound bar stand cover Suggestion of the sound bars and LCD TV arrangement. Slot in the sound bar into the sound bar stand and fix its cover as shown. (Model HT-SL75 : for 60" (152 cm) and 70" (177 cm) TV) (Model HT-SL70 : for 52" (132 cm) TV) LEFT Slot in the wire inside the groove or slit for better wire arrangement. (For model HT-SL70) (For model HT-SL75) 46" (117 cm) TV 176 mm (6 - 15/16”) RIGHT 52" (132 cm) TV 60" (152 cm) TV 70" (177 cm) TV Groove to neatly arrange the wire in. E-5 1 2 3 4 5 6 7 1 9 2011 October 7 HT-SL70 System preparation (continued) Caution: ● Be very careful to prevent the sound bar from falling when mounting on the wall. — SHARP is not responsible for accidents resulting from improper installation. — Do not let children dangle on the sound bar once it is attached on the wall as it can cause damage and injury. – 4 Screw the wall mount angle to the wall as shown in the illustration. (Total screw is 4 pieces) Wall mount angle Wall mount angle (screws x 2) Wall surface (screws x 2) Note: Make sure all screws are fully tightened. (screws are not supplied) ■ Driving screws Installing the sound bar wall mount angle. 22 mm (7/8" ) ■ 1 Align the wall mount slot at the sound bar to the 2 Slot the sound bar into the wall mount angle. Wall surface 1 Fix the pattern paper to the wall in horizontal Falling prevention Pattern paper 2 Make a hole on the wall following the screw point marks on the pattern paper by using a drill. 32 mm (1-1/4") 8-9 mm (3/8") Wall surface Safety wires (not supplied) are useful to prevent the sound bar from falling off the table. 3 Fix a wall mount plug (not supplied) into the hole using a hammer, until it is flush with the wall surface. 32 mm (1-1/4") 8-9 mm (3/8") Wall surface Loop the safety wires (not supplied) into each hole as shown and tie the safety wires to the LCD TV stand. E-6 1 2 3 4 5 6 7 8 9 10 2011 October 7 HT-SL70 ZB056 Placing the system Installation image: Notes: ● As the sound from the system is omni-directional, you TV can place the speaker anywhere you like. However, it is recommended to place it as close to the TV as possible. Caution: Do not change the installation direction when the unit is turned on. aCTIVE SUBWOOFER SYSTEM HT-SL70 BD Player DVD player SUBWOOFER SYSTEM Place the system as shown. [. . . ] — Volume cannot be ● Check if the HDMI CEC is Periodically wipe the cabinet with a soft cloth. Caution: ● Do not use chemicals for cleaning (petrol, paint thinner, etc. — Please change to HDMI/ ● Background noise appears when connecting with headphone output of TV-Terminal. This effect may occur depending on your used TV-Brand, model and age, and it is not the sound bar problem! [. . . ]