User manual SHARP FO-330

[. . . ] 6 seconds (only when ECM is on) Horizontal: 8 pels/mm Vertical: Standard: 3. 85 lines/mm Fine /Halftone: 7. 7 lines/mm Super fine: 15. 4 lines/mm 10 pages max. (Letter/A4, 80 g/m2 paper) Thermal transfer recording 64 levels MR, MH, MMR Approx. 50 Letter/A4 size sheets (at room temperature; maximum stack height should not be higher than the line on the tray) Legal: 5 sheets Memory size* Modem speed Transmission time* Resolution Automatic document feeder Recording system Halftone (grayscale) Compression scheme Paper tray capacity (60 - 80 g/m2 paper) *Based on Sharp Standard No. 1 Chart at standard resolution is Sharp special mode, excluding time for protocol signals (i. e. , ITU-T phase C time only). 1 Display 16-digit LCD display Applicable telephone line Public switched telephone network Compatibility Input document size ITU-T (CCITT) G3 mode Automatic feeding: Width: 148 to 216 mm Length: 140 to 297 mm Manual feeding: Width: 148 to 216 mm Length: 140 to 600 mm 210 mm max. Single / Multi (99 copies/page) Yes (cannot be used if power fails) 220-240 V AC, 50/60 Hz 5 - 35°C 25 - 85% RH Standby: 3. 6 W Maximum: 110 W Width: 327 mm Depth: 193 mm Height: 163 mm Approx. [. . . ] Dialling and transmission If you are making a phone call, lift the handset. Dialling begins. Note: If a fax transmission is unsuccessful and DOCUMENT JAMMED appears in the display, remove the document as explained on page 84. (This may occur if the other fax machine doesn't respond properly when you attempt to send the document. ) Automatic redialling If you use automatic dialling (including Direct Keypad Dialling) to send a fax and the line is busy, the fax machine will automatically redial the number. The fax machine will make three redial attempts at an interval of five minutes. During this time, RECALLING will appear in the display, followed by a two-digit number assigned to the fax job. You will not be able to dial any other locations while the message appears. 54 Sending a Fax by Automatic Dialling To stop automatic redialling, press STOP . Under certain conditions (for example if a person answers the call on a telephone), automatic redialling may stop before two redialling attempts are made. Error Correction Mode The fax machine is set to automatically correct any distortions in a transmission due to noise on the telephone line before printing at the receiving end. ECM is effective for both transmissions and receptions, and is only effective when the other fax machine has ECM as well. This will increase slightly the amount of memory available for memory transmission and reception. 1 2 3 4 5 Press FUNCTION once and once. Display: OPTION SETTING Press once and 5 times. ECM MODE Press once. 1=YES, 2=NO Press 1 to select YES, or select NO. STOP 2 to The display briefly shows your selection, then: RECEIVE RATIO Press to return to the date and time display. 55 3. Sending Faxes Sending a Fax From Memory Sending a Fax From Memory You can scan a document into the fax's memory and send the document from memory. This increases transmission speed and allows you to send a fax to multiple destinations in a single operation. After transmission, the document is automatically cleared from memory. Broadcasting (sending a fax to multiple destinations) This function allows you to send the same fax to as many as 20 different locations in just one operation. When sending to multiple locations, only auto-dial numbers can be used to dial the numbers of the receiving machines. 1 Load the document(s). · If desired, press RESOLUTION/ RECEPTION MODE to set the resolution and/or contrast. 2 3 4 5 Press START/MEMORY Press (or ) until the name of the number appears in the display (if no name was stored, the number will appear). Press to select the number. Repeat Steps 3 and 4 for each of the other locations to which you wish to send the fax (maximum of 20). · To check your selected locations, press to scroll through them. If you use a computer fax modem to send documents on the same line, you must turn this function off in order to prevent your fax from mistakenly attempting to receive documents from the computer fax modem. Follow the steps below to change the setting. 1 2 Press FUNCTION once and once. Display: OPTION SETTING Press once and 5 times. FAX SIGNAL RX 63 4. Receiving Faxes · The above step is necessary if you have set the Fax Signal Receive setting Optional Reception Settings 3 4 Press once. 1=YES, 2=NO Press 1 to turn on the function, or The display briefly shows your selection, then: 2 to turn it off. ECM MODE 5 Press STOP to return to the date and time display. Changing the number for remote fax activation If desired, you can use a number other than 5 to activate fax reception from an extension telephone. You can select any number from 0 to 9. 1 2 3 4 Press FUNCTION once and once. Display: OPTION SETTING Press once and once. FAX REMOTE # Press once. ENTER (0-9) (5) Enter the desired number (any number from 0 to 9). Example: 3 The display briefly shows your selection, then: TRANSACTION 3 5 Press STOP to return to the date and time display. 64 Optional Reception Settings Reception Ratio The fax has been set at the factory to automatically reduce the size of received documents to fit the size of the printing paper. If desired, you can turn this function off and have received documents printed at full size. If a document is too long to fit on the printing paper, the remainder will be printed on a second page. In this case, the cut-off point may occur in the middle of a line. Automatic reduction may not be possible if the received document is too large, contains too many fine graphics or images, or is sent at high resolution. In this case, the remainder of the document will be printed on a second page. 1 2 3 4 Display: Press FUNCTION once and once. OPTION SETTING Press once and 4 times. RECEIVE RATIO Press once. 1=AUTO, 2=100% Press 1 to select AUTO, or select 100%. 2 to The display briefly shows your selection, then: PRINT CONTRAST 5 Press STOP to return to the date and time display. 65 4. Receiving Faxes Substitute Reception to Memory Substitute Reception to Memory In situations where printing is not possible, such as when your fax runs out of paper, the imaging film needs replacement, or the paper jams, incoming faxes will be received to memory. When you have received a document in memory, FAX RX IN MEMORY will appear in the display, alternating with ADD PAPER & PRESS START KEY or CHECK FILM / CHECK COVER / CHECK PAPER JAM. When you add paper (and press START/MEMORY ), replace the imaging film, or clear the jam, the stored documents will automatically print out. 66 5. [. . . ] · · ( ) . : ( ) DOCUMENT JAMMED . : { | } ' _ ^ [ ] @ < = > ; : - , + ( ) ' & % $ # " ! (Automatic Dialling) : : <NEW NUMBER> . (Automatic Dialling) . [. . . ]