User manual SHARP ERA330 BROCHURE

[. . . ] (1) Creating the master list (subwindow program) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2) Deleting a machine from the master list (subwindow program). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifying the terminal to serve as a backup master -- master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifying whether to enable or disable the system retry function when a transmission error occurs -- master and satellite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · For the code entry system: Enter a corresponding clerk code and press the CLK key. # The pop-up window for the secret code will open, if secret code is programmed. Enter a secret code and press the ENTER key. NOTE · · · · The sign-on operation can be made only for one clerk at a time. If a clerk attempts to sign on when another clerk has already signed on, a lock error will occur. Every clerk that is listed in the system can sign on at any satellite. If a clerk has signed on at a machine, any other clerk cannot sign on at any other machine in the system using the clerk code of that clerk until he or she signs off. · In case of trouble, the sign-on state can be cleared at the master. 30 5. Sign-off operation (cancellation of clerk assignment) The sign-off operation is intended to cancel the assignment of a clerk to a machine and terminate his or her entry operation. The sign-off operation at a machine (master or satellite) can be done only for the clerks who have signed on at the machine. Sign-off procedure · For the real clerk key system: Pull out the inserted clerk key. · For the clerk entry key system: Press the clerk entry key that you pressed to sign on, again. If a satellite looks up the GLU/PBLU file in the master or asks the master to update the file, the backup master performs the same process as the master. 34 9. Drive-through data is either centrally controlled by the master or Individually looked up at each terminal. Automatic code generation Drive-through codes are generated automatically: when the end code for a transaction is generated, the start code for another transaction is automatically generated. Automatic look-up As drive-through codes are temporarily finalized by pressing the NBAL or FINAL key, data for these codes is automatically looked up in the same sequence as the code was generated. Drive-through-related inline communications are made for the following purposes: · · · · · New order or re-order Payment entry or temporary finalization Slip printing Bill transfer/bill totalizing Bill separating The drive-through data is transmitted from the master to a satellite for drive-through file look-up (in case of a new order/re-order). In this case, the drive-through reserve counter is retained at the master. The data is transmitted from a satellite to the master for finalization of a transaction (in case of a payment entry or temporary finalization). The data transmitted from the satellite is once saved in the drive-through data receiving file and then in the drive-through file. In this case, the drivethrough reserve counter is cleared at the master. 35 10. T-LOG polling All REG-mode transaction data in each satellite is saved in its T-LOG buffer. T-LOG polling is a data collecting system in which the master collects data from the T-LOG buffers in satellites. [. . . ] Replacement of the paper roll When a colored dye appears on the paper roll, it means that it is time to replace the existing paper roll. Replace the paper roll with a new one by using the procedures described below. When installing a paper roll for the first time, take steps 1 and 4 through 7. 1. Press the line feed switch to remove the paper remaining in the printer. 3 to 5 cm 4. Fold the top end of the paper roll by 3 to 5 cm securely as shown at left. How to fold paper 5. Insert the end of the folded paper deep into the paper chute of the printer and press the line feed switch to advance the paper. NOTE If paper is not inserted deep enough, it will not advance when the line feed switch is pressed. 6. Take up the slack in the paper and set the roll in position. 7. Pass the top end of the paper through the paper cutter on the paper cover and close it. 69 3. [. . . ]