User manual SHARP DV-NC230S(Y)

[. . . ] MODEL OPERATION MANUAL Please read this Operation Manual carefully before using your VCR/DVD COMBINATION. D V- N C 2 3 0 OPERATE OPEN/CLOSE PULL OPEN REW FF STOP/ EJECT OUTPUT PLAY REC TIMER (TRACKING) CH VCR DVD STOP PLAY 2 The region number for this VCR/DVD is 2. PAL ­1­ EN INFORMATION DVD FUNCTIONS VCR FUNCTIONS SETUP PREFACE DV-NC230S(Y) PRECAUTIONS VCR/DVD COMBINATION PRECAUTIONS SAFETY INFORMATION TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPARATUS TO DRIPPING OR SPLASHING, NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD BE PLACED ON THE APPARATUS. Laser Diode Properties Material: GaAs Wave length: DVD: 655 nm CD: 790 nm Emission Duration: Continuous Laser output: Max. 0. 8 mW Power Cord Protection To avoid any malfunctions of the VCR/DVD, and to protect against electric shock, fire or personal injury, please observe the following. · Hold the plug firmly when connecting or disconnecting the AC power cord. [. . . ] Make sure the remote control is in the VCR mode, then press TIMER ON/OFF. ·" " will not appear in the DVD mode. (OUTPUT on the front panel and VCR on the remote control will not function. ) · Once the VCR/DVD turns to the timer standby mode, no VCR functions · To cancel the timer standby mode, press TIMER ON/OFF on the remote control or STOP C/EJECT A on the VCR/DVD, then press VCR to activate the VCR function again. After an OTR and a Timer Recording has been set, this VCR/DVD operates as follows: · When Timer Recordings are set, the TIMER indicator on the front panel and " " will appear. To use the VCR as usual until the time for the recording, press TIMER ON/OFF so that the TIMER indicator on the front panel and " " disappear. Select either VCR or DVD mode, then continue with the other features as described in this manual. · The mode of the VCR/DVD and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you cancelled Timer Recording. Press VCR or DVD on the remote control to select your desired mode before you operate. ­ 17 ­ EN VCR FUNCTIONS VPS (Video Programme System) / PDC (Programme Delivery Control) While OTR or Timer Recording is performing. · If a tape runs out before an OTR or a Timer Recording is finished, the VCR/DVD ejects the tape and switches to the DVD mode automatically. Press TIMER ON/OFF on the remote control or STOP C/EJECT A on the VCR/DVD, then press VCR to activate the VCR function again. · Once the VCR/DVD switches to the DVD mode, all the VCR function will be unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording. · When you use the VCR/DVD in DVD mode during an OTR or a Timer Recording, the VCR/DVD will not turn off automatically even if the end time of the OTR or Timer Recording has been past. Note (for Timer Recording) : · If there is a power failure or the VCR/DVD is unplugged for more than 1 hour, clock and all timer settings will be lost. · If you want to use the VCR/DVD during a Timer Recording or while " " is on or flashing, Press OPERATE to turn on the VCR/DVD. Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don't need to set the TIMER off to use the DVD. When an OTR or a Timer Recording is completed. . . · If the other Timer Recordings remain as programmed, the VCR/DVD switches to the DVD mode automatically, and the TIMER indicator on the front panel lights up to indicate the VCR/DVD is in the timer standby mode. In some occasions, however, the VCR/DVD may be automatically turned off, instead of changing to the DVD mode after pressing TIMER ON/OFF. To avoid overlap of Timer Programming . . . · A timer programme will not work while another programme is under execution. Programme 1 Programme 2 Programme 3 9:00 10:00 11:00 · The TIMER indicator on the front panel flashes if there are no more Timer Recordings on standby. If you want to use the VCR function, press TIMER ON/OFF on the remote control or STOP C/EJECT A on the VCR/ DVD. Then press VCR to activate the VCR function. Direct Dubbing VC R DVD 1 4 7 2 5 8 0 3 6 9 +10 P LAY S TOP press first. 4. Select the desired tape speed. SP VCR/DVD COMBINATION NA527AD Refer to page 7 to switch between the VCR mode and the DVD mode. Insert a tape. · If necessary, rewind or fast forward the tape to the point at which you want to begin recording. Tape Type Tape S peed E -60 E -120 E -180 E -240 R ecording / P layback Time S P Mode LP Mode 1 hour 2 hours 2 hours 4 hours 3 hours 6 hours 4 hours 8 hours 5. Recording starts. with erase-protection tab 2. Press 0, 0, 4 to select DISC. DISC 7. To Stop Recording. To Stop Playback. VCR FUNCTIONS or TV Screen Hint · Press STILL/PAUSE F at the point where you want to start recording when you do dubbing middle of the DVD. · To stop recording temporarily, press STILL/PAUSE F after press VCR. Press STILL/PAUSE F again to resume recording. Copying a Video Tape Warning: Unauthorised recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR/DVD(this unit), playing VCR(another VCR) and your TV as outline in the following diagram. Scart cable (commercially available) (Back of Recording VCR/DVD) (Back of TV) AERIAL To SCART terminal RF OUT To SCART terminal (Back of another source) Scart cable (commercially available) 1. Insert a tape with its erase-protection tab into the recording VCR/DVD. Press TAPE SPEED on the remote control of the recording VCR/DVD to select the desired recording speed (SP/LP). Select the "AV2" or "AV3" position on the recording VCR/DVD. [. . . ] · Check if the INTERLACE/PROGRESSIVE mode is set correctly according to your TV. Audio or subtitle language does not · The selected language is not available for audio or subtitles on the DVD. The camera angle cannot be · The DVD does not contain sequences recorded from different camera angles. Audio or subtitle language cannot be · The DVD does not contain audio source or subtitles in the selected language. [. . . ]