User manual SHARP CD-ES770

[. . . ] To obtain the best performance from this product, please read this manual carefully. CD-ES770 Mini Component System consisting of CD-ES770 (main unit) and CP-ES770 (speaker system). MINI COMPONENT SYSTEM MODEL CD-ES770 OPERATION MANUAL Accessories Please confirm that the following accessories are included. Remote control 1 AM loop antenna 1 (RRMCGA049AWSA) (QANTL0005AWZZ) Note: Only the above accessories are included. FM antenna 1 (92LFANT1746A) CD-ES770 SPECIAL NOTES NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: While in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Selected disc number Adding tracks to the program: If a program has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original program. To check which tracks are programmed: While the unit is stopped in the programmed play mode, press the or button. Notes: When a disc with programmed tracks is ejected, the program is automatically canceled. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During programmed play, the DIRECT PLAY buttons will not work. 1 While in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. 2 Press one of the 1 - 5 buttons to select the desired disc. CD Playback 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. Repeat steps 2 - 4 for other tracks. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR/DIMMER button. Press the / button to start playback. 6 7 20 Listening to the radio Tuning CD-ES770 1 2 3 Press the ON/STAND-BY button to turn the power on. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). or ) button to tune in to the desired Notes: When radio interference occurs, auto scan tuning may stop automatically at that point. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. FM stereo mode indicator Auto power on function: When you press any of the following buttons, the unit turns on. TUNER (BAND) button (main unit and remote control): The unit turns on and the "TUNER" function is activated. / button (main unit and remote control): The unit turns on and playback of the last function starts (CD, TAPE, TUNER, GAME/VIDEO). FM stereo receiving indicator 21 Radio Manual tuning: Press the TUNING button as many times as required to tune in to the desired station. Auto tuning: When the TUNING button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. CD-ES770 Listening to the radio (continued) Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) To recall a memorized station Press the PRESET ( or select the desired station. ) button for less than 0. 5 seconds to 1 2 Perform steps 1 - 3 in "Tuning" on page 21. [. . . ] Contact your local CD software dealer for options. NO YES Correct Cleaning the cabinet Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth. Caution: Do not use chemicals for cleaning (gasoline, paint thinner, etc. ). It may cause malfunctions. 34 Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. [. . . ]